Antenna wire SL - SuperLight The super-light and high-strength stranded antenna wire is specially manufactured for use as long wire, end-fed, dipole or other antennas. The antenna strand is only 1.6 mm thick and consists of 6x0.25 mm tinned copper braiding. It has a core of tear-resistant Vectran fibers® and a weatherproof PE insulation. This gives it a maximum breaking load of up to 60kg! The low weight of only 4g per meter makes it ideal for mobile operation, DX expeditions SOTA, IOTA, COTA or POTA. Super light antenna wire Weight only about 4g/m 6x0.25mm copper braid, tinned Core made of Vectran fibers® Cross-section approx. 0.3 mm2 Insulation made of waterproof PE (polyethylene), black Diameter: 1.6 mm Maximum breaking load approx. 60 kg

Seal for SO-239 or N flange connectors High-quality rubber seal for sealing the flange connectors, for example in our End Fed kits. Suitable for our 4-hole SO-239 and N flange bushes, with 3mm bore.

NITTO 15 - Self fusing butyl rubber tape 19mm x 5m Ideal to protect your coax connectors from weather and moisture Excellent heat/cold resistant capabilities. The tapes are unified by fusing together. Excellent electrical properties. Completly self-amalgimates in two hours A self-fusing tape which utilizes properties of remarkably heat-resistant, weather-resistant self-fusing tape and silicone resin. Meets a wide range of needs, from insulating material for electric equipment, to insulation, protection, and bundling of automobile wire harnesses. Characteristics of Notto No. 15 Nitto 15 has an excellent volume resistivity, a high breakdown voltage and a low dissipation factor. It is totally resistant to moisture, water and chemicals.Nitto 15 offers excellent electrical insulation, workability and weather protection. The product has a superior weatherability and ozone resistance and because of the linerless system a very short application time. It completely self-amalgamates in two hours. Application Nitto 15 can be used for termination, splicing and corrosion protection of cables. Also insulation and protection of lead shielded cables is possible. The product is used for its waterproof sealing and corrosion protection of cables in marine and off-shore environments. Application temperature: min. –10 °C and max. 40 °CMaximum service temperature: continuously 65 °C and short periods 100 °CAbove 40 °C the tape begins to amalgamate to itself and can become difficult to unwind.

Flexible radiator M6 40cm long and flexible radiator with M6 stainless steel thread. Fits all MegActiv MA305 and Boni-Whip with M6 thread (Boni-Whip 2017 or later). This new radiator brings around 3dB more gain.

Rope clamp Clamcleat® CL260 - pack of 10 pieces Self-locking rope clamps made of high-strength, UV and cold-resistant material (tested in arctic conditions). Easily adjustable and retightenable at any time. For ropes of 2-4mm diameter. Ideal for Hamrope PES4. Material: nylon, color olive green or black, supplied in a pack of 10.

Adapter connector BNC female / PL/UHF male

Through Window or Door Connector Cable with BNC or PL connectors. Thourgh window cable Description: Flat coax cable, for feeding coax cables through windows and doors, For use with coax-cable. Saves drilling, for windows, doors,caravans and balconies.  Typ. insertation loss: up to 30MHz: <1dB up to 50MHz: < 2dB up to 75MHz: < 3.5dB up to 150MHz: <5dB Length with connectors: 30 cm (11,8") Length of the ribbon cable 20 cm (7,9") RX-Only!

Galvanic Antenna Isolator GI1000 The GI1000 suppresses noise reaching the ground connections on the receiver. The GI1000 covers a wide-band range of 50 kHz - 1000 MHz (typ. 1db insertion loss). The unit can be used in many receiving applications, It will also work with frequencies up to 1,25 GHz but the insertion loss may increase by up to 3db. The unit also has integrated double over-voltage protection and input and output are blocked for DC voltage. The galvanic isolator GI 1000 separates the path of the direct current between the outer shield of the coax cable and the shielding of the antenna feeding line in order to suppress interference caused by potential differences. This is achieved by using a small toroidal transformer. The inner conductor of the coax cable is insulated with capacitors providing coarse and fine voltage surge protection. Specifications: Excellent protection against sheath waves and voltage surges.Double voltage surge protection. On the antenna side Gas Discharge tube with an ignition voltage of 90v. On the receiver side you will find an ESD-diode (30KV; max.pulse power 350W (8/20μs) Input and output has been blocked for direct currents of max. 50V. The GI 1000 is very useful for owners of a PERSEUS SDR who still own the original switching power supply. This little troublemaker has made life hard for many a PERSEUS owner. Caution: Only suitable for reception purposes, high RF performance (> + 10dBm) cause permanent damage!

Adapter connector PL259 to BNC

Spiderbeam 12m HD Mast Der Spiderbeam Heavy Duty Fiberglasmast eignet sich perfekt zum Bau verschiedenster Antennen. Eine einzelne Person kann den Mast spielend leicht innerhalb weniger Minuten aufstellen. Speziell verstärkt und eigens entwickelt aufgrund unserer fortlaufenden Bemühungen nach noch besser belastbarem Portabel-Equipment! Dies sind extrem robuste Masten, mit deutlich dickerer Wandstärke (bis zu 2mm!) als die herkömmlichen "Angelruten". Sie sind in einer speziell verstärkten Wicklungsweise hergestellt - viele Lagen Fiberglas in abwechselnder Richtung (längs/quer) gewickelt ergeben eine deutliche Verstärkung in Längs- und Querrichtung. Stärkere Verbindungsstellen wurden außerdem durch eine deutlich größere Überlappung der einzelnen Rohrsegmente untereinander erreicht. Spiderbeam Heavy Duty Masten eignen sich prima zum Bau von 40/80/160m Draht Vertikals bzw. inverted L Antennen. (Lee W9OY hat damit z.B. eine leistungsfähige 80/40m Vertical aufgebaut)  Sie eignen sich ebenso gut für leichte 1-Ele Quads oder Delta Loops für 20-10m, oder auch Dipole für alle Bänder, besonders bei Speisung mit Hühnerleiter (die meisten Baluns sind ein bisschen schwer). Mit mehreren dieser Masten ist der Bau von Leichtbau-Beams für 40 oder 80m denkbar. Da sogar das oberste Segment 8mm Durchmesser (und 1.4mm Wandstärke) auweist, kann man diese Stangen auf der vollen 12m Länge benutzen - bei anderen Stangen sind die obersten Segmente meist so dünn wie eine Reitpeitsche und daher kaum zu etwas zu gebrauchen. Während unserer Tests konnten wir 80m inverted Vee Dipole (aus 1mm Kupferlackdraht) ganz oben in der Mastspitze befestigen, was mit einer "Angelrute" auf keinen Fall möglich ist. In 9-10m Höhe lassen sich ohne Probleme kleine VHF/UHF Yagis befestigen. Der beste (und günstigste) Draht für solche Anwendungen (Vertikals, Loops, Dipole, etc.) ist 1mm Kupferlackdraht o.ä. Zum Abspannen eignet sich 1mm Angelsehne o.ä. hervorragend. Die ersten Prototypen wurden November/Dezember 2004 an der Nordsee bei Windstärken bis zu 120 km/h erfolgreich getestet! Seitdem wurden weit über 3000 dieser Masten weltweit erfolgreich installiert. Gleich bestellen und ab sofort Portabelfunk mit einem Profi-Mast der neuen Generation geniessen. Speziell verstärkter Profi Fiberglas-Teleskopmast volle Höhe (Länge) 12m Transportlänge 1.18m Gewicht 3.3kg Durchmesser unten 55mm Durchmesser oben 8mm Wandstärke 1.4mm (oben) - 2mm (unten) Anzahl der Segmente 12 Material Fiberglas, schwarz, UV beständigmehrlagig gewickelt und speziell verstärkt     -------------------------------------Hersteller: Nach EU 2023/988 Produktsicherheitsverordnung (GPSR) Spiderbeam GmbH Geschäftsführer: Dipl.-Ing. Cornelius Paul Otto-von-Guericke-Str. 3 03130 Spremberg Deutschland Tel: +49 3563 989812 Fax: +49 3563 989812 E-Mail: office@spiderbeam.com Verantwortliche Person: Spiderbeam GmbH Geschäftsführer: Dipl.-Ing. Cornelius Paul Otto-von-Guericke-Str. 3 03130 Spremberg Deutschland Tel: +49 3563 989812 Fax: +49 3563 989812 E-Mail: office@spiderbeam.com

Hamrope PES 4 Our best selling universal guy line for the radio amateur. For portable and stationary use. The quality polyester has excellent UV resistance and is suitable for long-term use. The elasticity of this braided rope has a shock absorbing effect and is desirable and often necessary for the use of radio amateurs. The attractive design allows the product to fit well into a natural environment, yet be perceived sufficiently. Hamrope PES 4 Polyester, 4mm diameter tensile strength approx. 260 daN(~Kg) Colour: olive green with red marker Length: 50 meter

Hamrope PES 4 Our best selling universal guy line for the radio amateur. For portable and stationary use. The quality polyester has excellent UV resistance and is suitable for long-term use. The elasticity of this braided rope has a shock absorbing effect and is desirable and often necessary for the use of radio amateurs. The attractive design allows the product to fit well into a natural environment, yet be perceived sufficiently. Hamrope PES 4 Polyester, 4mm diameter tensile strength approx. 260 daN(~Kg) Colour: olive green with red marker Length: 50 meter

CCMC30 Common Mode Noise Filter Noise filters are nothing new and are often used for transmitting purposes. They are used to prevent unwanted radiation via the coax shielding. It is less known that they can also suppress unwanted radiation when receiving signals, especially when an active antenna is used. However, in this case, the situation is reversed: en route to the antenna, unwanted interferences from electric home appliances can be effectively eliminated. NTi's Coaxial Common Mode Noise Filter (CCMC30) has been especially optimized for maximum common mode noise rejection of >30dB wide band in the frequency range of 150kHz - 30MHz. With slight limitations a much wider frequency range is covered. In the medium wave range for example a noise suppression of up to 45 dB can be achieved. This is possible by using a cascaded system of ferrite cores with various frequency dependent material properties, combined with high quality coaxial cable. For outdoor use, the system is housed in a water-proof enclosure. We recommend to connect the CCMC30 as closely as possible to the receiver.With regard to efficient noise suppression, the CCMC 30 is not very much different from the galvanic isolator GI1000. However, the CCMC30 performes down to lowest frequencies including DC voltage, in contrast to the GI1000, which blocks DC voltages and very low frequencies. The CCMC30 can thus be connected directly to the coax cable which passes the supply voltage or the control signals to the active antenna. A series connection of the GI1000 directly connected to the receiver followed by the CCMC30 right behind the power inserter may result in an even better performance. Technical Data Guaranteed frequency range: 150 kHz – 30 MHz Common Mode Wave suppression: >30 dB: 150 kHz -30MHz (>20 dB: 30kHz-60MHz) Insertion loss: <1 dB (up to max. 150 MHz) Size: 100x68x50mm (132mm with BNC connectors) Connectors: 2x BNC 50Ohms Weight: 320g Made in Germany

This USB cable enables the 5V power supply of the CPI1500UNI via a USB connection. With this little helper "USB barrel plug adapter" you can easily supply the CPI1500UNI power inserter with the USB socket from the computer, power bank etc. Specification • Connectors: 1 x USB Typ A > DC barell plug• Voltage: 5 V• Cable lenght: ca. 1 meter Specification of the power connector • Masse außen, Plus inner• Maße:  inner: ø ca. 2,1 mm  outer: ø ca. 5,5 mm  Length: ca. 12,5 mm

Mini telescopic pole with only 71cm transport length, fits in any suitcase. This pole is easy to carry and ready installed within a minute. Although it is light and small enough to fit in any large suitcase, it was developed to be rugged and durable! This ultra-portable Mini pole has a heavy-duty screw-on base cap at the bottom to protect its segments from rocks and mud. Nubs on the bottom of the pole help prevent slippage. Spiderbeam fiberglass poles are extremely strong, with a much greater wall thickness than the typical "fishing rod" types.It uses a special reinforced winding technique – where several layers of fiberglass are wound in alternating direction (criss-cross wound) – providing greatly increased lateral and linear strength. The Spiderbeam Mini-poles have a much larger overlap between segments than most other fiberglass poles, which assures stronger joints between segments, and results in a much stronger pole. Spiderbeam fiberglass poles are perfect for supporting all kinds of wire antennas.The Spiderbeam Mini poles are great for Geocaching, SOTA, IOTA and any other popular application for traveling ham radio operators. The top segment of the Mini pole is hollow, very rigid and got has a usable inner diameter of 4mm allowing a wire to pass through, or for attaching your mini tool for other applications. Unlike most competitors’ poles where the top segment is a very thin, solid whip, the Spiderbeam Mini pole can be used to its full 7m or 10m length. Technical Data 7 Meters / 23ft fully extracted length (height) 7m (23ft)* transport length 0.71m (2715/16)* weight 1026g (2lbs. 4 oz.) bottom diameter (incl. the cap) 50mm (2")* top diameter 6mm (0.24")* wall thickness 0,7mm - 1,4mm* (0.027" - 0.067")* number of segments 11 pole material black fiberglass, UV protected specially reinforced multilayer winding Technical Data 10 Meters / 32ft fully extracted length (height) 10m (32ft 10")* transport length 0.72m (281/3)* weight 2.220kg (4lbs. 14 oz.)* bottom diameter (cap) 66mm (2 3/5")* bottom diameter (segment) 60mm (21/3")* top diameter 6mm (0.24")* wall thickness 0.7mm - 1.4mm* (0.027"" - 1/18")* number of segments 17 pole material black fiberglass, UV protected specially reinforced multilayer winding

This V4A mounting bracket fits for the Boni-Whip, MegActiv, GigActiv and the MegaLoop.

Schäkel aus A4 Edelstahl und 5mm stärke.  SWL /WLL daN: 270

Antenna wire SL - SuperLight The super-light and high-strength stranded antenna wire is specially manufactured for use as long wire, end-fed, dipole or other antennas. The antenna strand is only 1.6 mm thick and consists of 6x0.25 mm tinned copper braiding. It has a core of tear-resistant Vectran fibers® and a weatherproof PE insulation. This gives it a maximum breaking load of up to 60kg! The low weight of only 4g per meter makes it ideal for mobile operation, DX expeditions SOTA, IOTA, COTA or POTA. Super light antenna wire Weight only about 4g/m 6x0.25mm copper braid, tinned Core made of Vectran fibers® Cross-section approx. 0.3 mm2 Insulation made of waterproof PE (polyethylene), black Diameter: 1.6 mm Maximum breaking load approx. 60 kg

Antenna wire SL - SuperLight The super-light and high-strength stranded antenna wire is specially manufactured for use as long wire, end-fed, dipole or other antennas. The antenna strand is only 1.6 mm thick and consists of 6x0.25 mm tinned copper braiding. It has a core of tear-resistant Vectran fibers® and a weatherproof PE insulation. This gives it a maximum breaking load of up to 60kg! The low weight of only 4g per meter makes it ideal for mobile operation, DX expeditions SOTA, IOTA, COTA or POTA. Super light antenna wire Weight only about 4g/m 6x0.25mm copper braid, tinned Core made of Vectran fibers® Cross-section approx. 0.3 mm2 Insulation made of waterproof PE (polyethylene), black Diameter: 1.6 mm Maximum breaking load approx. 60 kg

7,5  Volt plug AC Adapter with additional noise filter Low noise unstabilizied 7,5 Volt max. 150mA plug power supply adapter with transformer (no switching power supply). 230 Volts only! This power supply is linear regulated and is no switching power supply. A "real" transformer is installed. Good for active antenna applications such as MegaLoop, MegActiv, MegaDipol and GigActiv. With additional noise filter Interference suppression for network-related interference at the output: 150kHz - 30MHz:> 25dB In the medium wave range even> 40dB Technical data Input: 230V AC / 50Hz / 3,6 W Output: 7,5 V DC / max. 150 mA  (10,5 Volt idle) Dimensions without connectors: 75 x 55 x 60mm Weight: 100 grams Euro Plug Made in Germany

Diese kleine, gefütterte Segeltuchtasche mit Tragegurt und robustem Reißverschluss, passt perfekt zu den Spiderbeam Fiberglasmast 12m HD, mit 12m Länge. In dieser Tragetasche, mit gesticktem Logo, lässt sich der Spiderbeam 12m HD bequem und gut geschützt transprotieren oder einlagern. Abmessungen Länge: ca. 126cm Breite: ca. 9cm Gewicht ca. 200g -------------------------------------Hersteller: Nach EU 2023/988 Produktsicherheitsverordnung (GPSR) Spiderbeam GmbH Geschäftsführer: Dipl.-Ing. Cornelius Paul Otto-von-Guericke-Str. 3 03130 Spremberg Deutschland Tel: +49 3563 989812 Fax: +49 3563 989812 E-Mail: office@spiderbeam.com Verantwortliche Person: Spiderbeam GmbH Geschäftsführer: Dipl.-Ing. Cornelius Paul Otto-von-Guericke-Str. 3 03130 Spremberg Deutschland Tel: +49 3563 989812 Fax: +49 3563 989812 E-Mail: office@spiderbeam.com  

4-hole N flange connector With PTFE insulation (high temperature resistant) and gold-plated center contact.

1 – 30 MHz Common mode filter with bifilaire windings for optimal attenuation There are many types of common mode chokes available, HF Kits opts for a common mode choke with bifilar windings for optimal filtering. This 1 – 30 MHz common mode current filter is optimized for the 80 and 160 meter band. In this case a FT240-31 toroidal core with optimal performance for the lower frequency range is used. The 1 – 30 MHz common mode choke performs very well on the entire HF spectrum. The attenuation is therefore around 30 dB across the entire HF frequency spectrum. This filter is therefore a real all-rounder for amateurs who want to work from 160 meters to 10 meters. Even people who deal with LPAM (Medium Wave) can use this filter. The main reason for using a common mode choke is to ensure that the coax cable’s shield does not become part of the antenna system and will radiate unintentionally. This has all sorts of nasty effects, think of: interference issues, disrupted radiation pattern of the antenna and a higher noise level. This last point is because not only does the coax cable’s shield radiate when you transmit, but the shield also works as a receiving antenna. Because the coax cable often makes a considerable trip within the house, close to interference sources (mains, PLC etc…) It is useful to eliminate these sources of interference. Any way, Good reason to use a common mode choke. The effect of this common mode choke with bifilar windings is difficult to predict. This depends on local circumstances. Think of: antenna type, antenna placement, type of feed line, feed line placement and especially local sources of interference. There are manufacturers that promise in advance a significant drop in interference, however this is not real. There are cases where the noise level decreases by two to three S points, but also cases where the filter has almost no effect. This kit includes: IP65 enclosure 100 x 100 x 55 mm (Polycarbonat) Ringcore Amidon FT240-31 Winding wire 18 AWG – 4x 85cm PTFE 19 x 0.25 mm copper “Silver plated” Toroid mounting plate Stainless steel M3 6mm screws 4x Stainless steel M3 Spring washer 4x 2x PL 259 Chassis 2x M3 cable lug 8x Stainless steel M3 Bolt 12mm 8x Stainless Steel M3 Nut 8x Stainless steel M3 washer 8x Stainless steel M3 tooth washer IMPORTANT! Do not place the common mode choke in case of an End Fed antenna directly at feed point of the antenna.Construction Manual in Englisch

2 piece suction cup for easy attachment of the Loop wire of our MegaLoop FX, ML200, ML060 and ML052 on the window or smooth surfaces. Ideal for travel or home.

Enclosure for mini Endfed Antennas Polycarbonate Single enclosure of our mini EndFed antenna kits as a spare part or just for experimenting. The enclosre is made of polycarbonate, as in the kit. Polycarbonate housings are more weather-resistant and UV-resistant than ABS housings. Dimensions: 64x58x35mmColour: light greyMaterial: polycarbonateProtection class: IP 65Screws and gasket included

PowerBank  Actually this PowerBank is intended for charging smartphones. But this model can also power our antennas: MegaLoop, MegActiv 305 and GigActiv 3005, autonomously and noise-free. Ideal for mobile use. 5V with 4000mAh, including USB 3.0 connection cable (approx. 10 cm long) Technical specifications Input voltage: DC 5 V, ≥ 500 mA (USB compatible) Output voltage: 4.2 V ± 1% (charging slot) / 5 V ± 5% (USB) Output current: 2 x 1A MAX (charging slot) / 2A MAX (USB) Dimensions: 94 mm × 44 mm × 25 mm Weight: 46.5 g (without connection cable) Scope of delivery: Powerbank with 2x18650 LI-ION batteries (2x 2000mAh), 2x retaining rubber, 1x USB 3.0 connection cable

Adapter connector BNC male / N female 

Weatherproof housing for MegaLoop and MegaDipol This UV-protected and ventilated polycarbonate case protects your MegaLoop (all models since 2014) or MegaDipol from heavy rainfall and other extreme weather conditions like a second skin. A sliding stainless steel sleeve additionally protects the drain on the BNC connector. The screw connections for the radiating elements and grounding are led through to the outside and are also made of stainless steel. When operating in salty environments and near the sea, the weatherproof housing should definitely be used additionally. Our antennas are designed to be splash-proof, but salty capillary water can conquer even the best sealing gasket over time. The rear ventilated weatherproof housing effectively prevents direct contact of the antenna electronics with harmful weather influences.   Assembly Instructions You can find assembly instructions here: LINK

AntennaJet AAS300DP Aktiver 3-fach Antennenverteiler 9kHz - 300MHz (-450MHz*) Mit Dual Power! Großer Dynamikbereich Weiter Frequenzbereich: 9kHz - 300MHz (- 450MHz*) Hohe Intermodulationsfestigkeit Hohe Entkopplung der Ausgänge Hohe Rückwärts-Isolation Eingang ESD-geschützt Spannungsversorgung per USB oder Netzteil Made in Germany! Bonito's neuer Antennensplitter AntennaJet AAS300DP kann das Signal von einer Empfangsantenne auf bis zu 3 Empfänger nahezu ohne Verluste verteilen. Sein großer Frequenzbereich reicht von 9kHz - 300MHz (*mit kleinen Verlusten sogar bis 450MHz). Die interne Verteilung erfolgt über rauscharme, großsignalfeste Breitbandverstärker ohne gegenseitige Beeinflussung der Ausgänge. Der aktive Antennensignalverteiler AntennaJet AAS300DP verteilt ein Eingangssignal nahezu verlustlos an drei Ausgänge weiter. Bedingt durch die außerordentlich hohe Entkopplung der Ausgänge wird dabei eine gegenseitige Beeinflussung der angeschlossenen Empfänger vermieden. Ebenso wird dadurch die Abstrahlung von  möglicher Störstrahlung in Richtung Antenne wirkungsvoll unterdrückt. DualPower heißt: Stromversorgung per USB oder Netzteil Ab dem Modell 2017, lässt sich der AntennaJet AAS300DP Kurzwellen Antennenverteiler sowohl mit einem Netzteil (2,1mm Hohlstecker), als auch per USB mit Strom versorgen. Damit ist der AntennaJet noch flexibler geworden. Die USB-Versorgung hat den Vorteil, dass man A) kein externes Netzteil mehr braucht und B) den Antennensplitter auch autonom und rauscharm über eine separate USB-PowerBank versorgen kann. Durch die flexible Stromversorgung, dem geringen Stromverbrauch und seiner Kompaktheit ist der AAS300DP auch sehr gut portabel verwendbar. Es lassen sich bis zu max. drei Empfänger anschließen. Nichtangeschlossene Ausgänge können konstruktionsbedingt offen bleiben bzw. benötigen keinen Abschluss.Die Eingangsantennenbuchse ist mit einer ESD-Schutzschaltung gegen kurzzeitige bzw. pulsförmige Überspannungen und Überlastungen  geschützt.* * Der ESD Schutz ersetzt keinen Blitzschutz! Zur Montage des AntennaJets empfehlen wir unsere MB1 Halterung.  Technische Daten Eingangsfrequenzbereich: 9kHz - 300MHz (-1dB) (@ 450MHz -6dB)Eingangsbuchse/-impedanz: BNC / 50 Ohm (DC-geblockt max. 25V)ESD-Eingangsschutz: 30KV; max. Pulsleistung 350W (8/20µs)Max. zulässige Eingangsleistung: 0dBmDurchgangsdämpfung: max. 1.5dB typ.Ausgangssbuchsen/-impedanz: BNC / 50 Ohm (DC-geblockt max. 25V)Isolation zwischen den Ausgängen:70dB typ. <1MHz60dB typ. < 30MHz50dB typ. <100MHz35dB typ. <300MHzIsolation zwischen Ausgang und  Eingang (Rückwärts-Isolation):80dB typ. <1MHz70dB typ. <30MHz50dB typ. <100MHz35dB typ. <300MHz Amplitudendifferenz der Ausgänge:    max. 0.5dB typ.IP3 Intercept-Punkt dritter Ordnung:    +35dBm typ. <10MHz +20dBm typ. >100MHzStromversorgung: 5,5 – 12Volt DCAnschluss der Stromversorgung: USB-B Buchse oder 2,1mm HohlsteckerStromaufnahme: max.50mAArbeitstemperaturbereich: 0 - 40°C (ohne Betauung)Grösse / Gewicht: 115 x 90 x 32mm / 0.30kgKonformität: CE Optionales Zubehör:  Halterung MB1 USB A/B - Kabel (geschirmt mit Ferritkern) Bitte unbedingt  beachten: Der vorhandene ESD-Schutz ist nicht gleichbedeutend mit einem vollwertigen Blitzschutz; daher ist eine Haftung für angeschlossene Geräte grundsätzlich ausgeschlossen. Bei Nichtbenutzung, Abwesenheit, Sendebetrieb oder Gewittergefahr muss das Gerät immer von der angeschlossenen Antenne getrennt werden, um Schäden zu vermeiden.

Over Voltage Protector OVP1000 Small part, big impact!Triple protection against overvoltages on the antenna line: To protect your receiver we offer the OVP1000 a new surge (Over Voltage Protector). Built-in coaxial lines, so be high current pulses as generated by lightning strikes in the immediate vicinity derived. These protect the OVP 1000 on three counts against overvoltages on the antenna line: Antenna side: A gas discharge tube with 60V ignition voltage, max. Pulse discharge current 1 kA (8 / 20us) On the receiver side. An ultrafast diode ESD (30KV max pulse power 350W (8 / 20us) Input and output are also for DC voltages up to max. Blocked 100V Without replaceable cartridge, the system is completely replaced. Not waterproof. Extremely broadband deployment Frequency range: 200Hz - 1GHz (type 1 dB insertion loss.)RCA sockets: BNC Made in Germany Overvoltage protection OVP1000 in practical use I inserted the 1000 inline while listening to Old Time Radio on 6770 AM, on my beverage. Not only did it decrease clipping without attenuator inline, it eliminates the DC clips with attenuator engaged!!! I can say from experience, the OVP1000 is reasonably priced, protection device that offers no noticeable insertion loss of signal & obviously drops the induced static… Read the Article in the Bonito Newsroom    Please read carefully and Disclaimer:The OVP 1000 is no protection of the antenna line against direct lightning strike, since lightning always seeking kürzsten way to Earth, which does not necessarily take place via the coaxial cable. Therefore, the protection function is limited to overvoltages and potential differences between Koaxmasse (shield and inner conductor). Therefore, a liability for connected devices is generally excluded! When not in use, absence, broadcasting or lightning storms in the receiver should be disconnected to prevent damage from the antenna line! Made in Germany