NTi

Galvanic Antenna Isolator GI1000 The GI1000 suppresses noise reaching the ground connections on the receiver. The GI1000 covers a wide-band range of 50 kHz - 1000 MHz (typ. 1db insertion loss). The unit can be used in many receiving applications, It will also work with frequencies up to 1,25 GHz but the insertion loss may increase by up to 3db. The unit also has integrated double over-voltage protection and input and output are blocked for DC voltage. The galvanic isolator GI 1000 separates the path of the direct current between the outer shield of the coax cable and the shielding of the antenna feeding line in order to suppress interference caused by potential differences. This is achieved by using a small toroidal transformer. The inner conductor of the coax cable is insulated with capacitors providing coarse and fine voltage surge protection. Specifications: Excellent protection against sheath waves and voltage surges.Double voltage surge protection. On the antenna side Gas Discharge tube with an ignition voltage of 90v. On the receiver side you will find an ESD-diode (30KV; max.pulse power 350W (8/20μs) Input and output has been blocked for direct currents of max. 50V. The GI 1000 is very useful for owners of a PERSEUS SDR who still own the original switching power supply. This little troublemaker has made life hard for many a PERSEUS owner. Caution: Only suitable for reception purposes, high RF performance (> + 10dBm) cause permanent damage!

CCMC30 Common Mode Noise Filter Noise filters are nothing new and are often used for transmitting purposes. They are used to prevent unwanted radiation via the coax shielding. It is less known that they can also suppress unwanted radiation when receiving signals, especially when an active antenna is used. However, in this case, the situation is reversed: en route to the antenna, unwanted interferences from electric home appliances can be effectively eliminated. NTi's Coaxial Common Mode Noise Filter (CCMC30) has been especially optimized for maximum common mode noise rejection of >30dB wide band in the frequency range of 150kHz - 30MHz. With slight limitations a much wider frequency range is covered. In the medium wave range for example a noise suppression of up to 45 dB can be achieved. This is possible by using a cascaded system of ferrite cores with various frequency dependent material properties, combined with high quality coaxial cable. For outdoor use, the system is housed in a water-proof enclosure. We recommend to connect the CCMC30 as closely as possible to the receiver.With regard to efficient noise suppression, the CCMC 30 is not very much different from the galvanic isolator GI1000. However, the CCMC30 performes down to lowest frequencies including DC voltage, in contrast to the GI1000, which blocks DC voltages and very low frequencies. The CCMC30 can thus be connected directly to the coax cable which passes the supply voltage or the control signals to the active antenna. A series connection of the GI1000 directly connected to the receiver followed by the CCMC30 right behind the power inserter may result in an even better performance. Technical Data Guaranteed frequency range: 150 kHz – 30 MHz Common Mode Wave suppression: >30 dB: 150 kHz -30MHz (>20 dB: 30kHz-60MHz) Insertion loss: <1 dB (up to max. 150 MHz) Size: 100x68x50mm (132mm with BNC connectors) Connectors: 2x BNC 50Ohms Weight: 320g Made in Germany

Over Voltage Protector OVP1000 Small part, big impact!Triple protection against overvoltages on the antenna line: To protect your receiver we offer the OVP1000 a new surge (Over Voltage Protector). Built-in coaxial lines, so be high current pulses as generated by lightning strikes in the immediate vicinity derived. These protect the OVP 1000 on three counts against overvoltages on the antenna line: Antenna side: A gas discharge tube with 60V ignition voltage, max. Pulse discharge current 1 kA (8 / 20us) On the receiver side. An ultrafast diode ESD (30KV max pulse power 350W (8 / 20us) Input and output are also for DC voltages up to max. Blocked 100V Without replaceable cartridge, the system is completely replaced. Not waterproof. Extremely broadband deployment Frequency range: 200Hz - 1GHz (type 1 dB insertion loss.)RCA sockets: BNC Made in Germany Overvoltage protection OVP1000 in practical use I inserted the 1000 inline while listening to Old Time Radio on 6770 AM, on my beverage. Not only did it decrease clipping without attenuator inline, it eliminates the DC clips with attenuator engaged!!! I can say from experience, the OVP1000 is reasonably priced, protection device that offers no noticeable insertion loss of signal & obviously drops the induced static… Read the Article in the Bonito Newsroom    Please read carefully and Disclaimer:The OVP 1000 is no protection of the antenna line against direct lightning strike, since lightning always seeking kürzsten way to Earth, which does not necessarily take place via the coaxial cable. Therefore, the protection function is limited to overvoltages and potential differences between Koaxmasse (shield and inner conductor). Therefore, a liability for connected devices is generally excluded! When not in use, absence, broadcasting or lightning storms in the receiver should be disconnected to prevent damage from the antenna line! Made in Germany

MegaLoop FX Active Loop Antenna Probably the most flexible active loop antenna Ultra broadband frequency range from 9kHz - 180MHz High dynamic range with an IP of typ. +40 dB and IP 2 of typ. +85 dB Power requirements: 5V - 15V Selectable FM band stop filter with low pass function Selectable amplification in three steps Various radiating elements and sizes can be used Indoor and outdoor use Additional ground terminal (M5) on the enclosure High-quality craftsmanship; splash-water proof enclosure; all screw terminals made of stainless steel Small packaging = small shipping costs Ideal for outdoor use because dismountable and USB power supply The Megaloop FX is our latest active loop amplifier for the 9kHz to max. 180MHz range. It combines  all the outstanding features of the successful MegaLoop ML 200 and ML 052. Due to its integrated selectable FM band stop filter and the three-step amplification a maximum of flexibility for all kinds of use is possible. Flexible range of application This broadband magnetic loop antenna is especially suitable for places with difficult reception due to electrical interferences (E-field) in the near-field area, it is also made for indoor use or on the balcony/patio. You can put it up in the attic, at the window, on the balcony, in the carport fixed to the wall or permanently attached to a mast. Flexible FM-band stop filter Based on the well proven MegaLoop platform, an additional low pass filter and a FM-band stop filter were integrated which can be activated or deactivated with a jumper. In case of FM-interferences, the FM bandstop filter can be activated with a jumper and so FM signals between 88 MHz and 108 MHz will be attenuated by 25 - 40 dB. Flexible three-step amplification The gain of the MegaLoop FX can be adjusted in three steps by an internal jumper (High/Medium/Low)Frequency response (-3dB) and nominal amplification. a) FM-band stop off1. High Gain: 9 kHz - 110 MHz and 25 dB gain2. Medium Gain: 9 kHz - 150 MHz and 20 dB gain3. Low Gain: 9 kHz - 180 MHz and 15 dB gain b) FM- band stop on:1. High Gain: 9 kHz - 52 MHz and 25 db gain2. Medium Gain: 9 kHz - 60 MHz and 20 dB gain3. Low Gain 9 kHz - 66 MHz and 15 dB gain Flexible loop sizes The MegaLoop FX makes the most diverse radiating elements possible. As standard, a loop made of flexible PVC-coated and seawater-resistant (V4A) stainless steel wire is available. It comes as a 5m (16,40ft) circumference loop for indoor and portable as well as for outdoor use. Other lengths, such as 10m (32,81ft), are on offer. Even lengths up to 20m (65,62ft) have successfully been tested. Additionally, an aluminum rigid loop with a diameter of 40 cm or 80 cm is also available. Due to its versatility and adjustment of amplification, there will always be an ideal combination of the loop size and amplification. Excellent IP values with power supply as low as 5V With two signals in the 7 MHz range, an excellent IP3 value of typ. +40 dB and a IP 2 value of +85 dBm is achieved with mere 5 V ( max. 40mA) and so the loop can be powered via USB or power bank. A DualPower power inserter (bias tee) supply is included in the standard scope of delivery. The MegaLoop can be operated by two different kinds of power sources. It can be powered either by a conventional plug power supply (5,5 / 2,1mm round plug) or optional Cable via USB. Powering via USB has the advantage that no external power supply is needed and that the antenna can be operated independently and noise-free with a separate USB PowerBank. The supply voltage range is 5 - 15V DC (40mA max) and thus the antenna is also well suited for portable use. Integrated threefold surge protection of the active parts Coarse protection by gas arrester with 60V trigger voltage and a max. pulse leakage current of 1 kA (8/20µs) and by twofold additional integrated fine protection of max. 2 kV and 8 kV respectively. Additionally, the loop connections are connected to ground with high impedance to avoid static charges. Low shipping costs - no bulky item ! Since the antenna can be shipped as such a small parcel, there will only be standard postage and when ordering a rigid loop of 1m or 2m diameter you will already save about 35,-€ compared to shipping as a bulk item. Hint: With two suction cups you can attach the MegaLoop antenna to a window at home, in a hotel or when on the road. Because of its flexible loop, transportation is really a piece of cake. In our newsroom test " Design of a really portable SDR Part 2" I simply put the loop over the tailgate of our Caddy and was able to receive signals beautifully. You want to test the MegaLoop FX live on air? If you would like to test the MegaLoop FX live, you can now conveniently do this over the Internet with a KIWI SDR. Just click on this Link and you can browse the whole band from 10kHz to 30MHz. The linked KIWI-SDR with MegaLoop and 6,8 Meter Loop is located in northern Germany and can handle up to 4 users at a time. Scope of delivery MegaLoop FX 5m (16,40ft) PVC-coated, seawater-resistant stainless steel wire. Power inserter CPI 1500UNI Manual Made in Germany Recommendation Near the sea or in case of possible contact with salt water we strongly recommend the use of our weather protection case. Please note! The offered coax cables are custom-made and therefore not returnable / refundable.

LP060 Low Pass Filter The elliptically-formed low pass filter LP060 from NTi suppresses all frequencies above 60 MHz. Highly effective antennas combined with near-by strong FM stations often overburden the input of the radio and cause interference and phantom signals. The LP060 was developed aiming at the highest possible suppression in the 88MHz - 108 MHz FM band, whereas as the 6m amateur radio band at 50MHz is still totally within the pass band. For the greatest possible effectiveness, the low pass filter  should be inserted directly before the receiver input.  Attenuation values (typ.):52MHz: -1dB60MHz: -3dB80 MHz: -55dB88-110 MHz: -90dB110-150MHz: -75dB150-200MHz: -70dB200-400MHz: -65 dB Dimension: 88mm x 31mm x 25mm (3,46 x 1,22 x 0,98 inch) Input and output are DC-blocked (max. 50V DC) Attention: Only suitable for reception, high HF (>10dbm) will cause permanent damage! Successfully tested with: Elad FDM-S1 and FDM-S2, FiFi-SDR1.0 and 2.0, PM-SDR, Winradio Excalibur, RFSpace SDR-IQ Made in Germany

MegActiv MA305FT Wide Band Active Antenna Wide frequency range 9kHz – 300MHz Small dimensions Dual Power Supply: 5,5V – 15V Selectable FM band stop filter with low pass function Ideal for traveling, at home or DX-Camps IP3:>typ. +30dBm / IP2:>typ. +50dBm Enlarged and flexible 200mm radiating element The new MegActiv MA305FT is an evolution of the popular MegActiv MA305. In addition to small improvements in electronics, the new MegActiv MA305FT has been equipped with a switchable FM band-stop filter. Thus, disturbing radiation from the FM band between 88 and 108 MHz can be easily minimized The new MegActiv MA305FT close the gap between the Boni-Whip and the GigActiv GA3005 E-Field Antennas. This low noise active antenna, which is produced according to the highest standards, covers the frequency range between 9kHz and 300MHz. With a radiating element of only 22 cm / 8,66 inch it can be erected inconspicuously. It can be powered with 5-15 V DC (max.10mA) and alternatively with the supplied Power unit CPI 1500DP via USB. Flexible FM-band stop filter Based on the well proven Megactiv platform, an additional low pass filter and a FM-band stop filter were integrated which can be activated or deactivated with a jumper. In case of FM-interferences, the FM bandstop filter can be activated with a jumper and so FM signals between 88 MHz and 108 MHz will be attenuated by 25 – 40 dB. Flexible power supply The MegActiv MA305FT can be operated by two different kinds of power sources. It can be powered either by a conventional plug power supply (5,5 / 2,1mm round plug) or via USB with a optional Cable. Powering via USB has the advantage that no external power supply is needed and that the antenna can be operated  autonomously and noise-free with a separate USB PowerBank. The supply voltage range is 5 - 15V DC (10mA max) and thus the antenna is also well suited for portable use. You want to test the MegActiv MA305FT live on air? If you would like to test the MegActiv MA305FT active antenna live, you can now conveniently do this over the Internet with a KIWI SDR. Just click on this Link and you can browse the whole band from 10kHz to 30MHz. The linked KIWI-SDR with a MegActiv MA305FT is located in Bonn (DL0DTM Clubstation Deutsche Telekom) and can handle up to 4 users at a time. Features Integrated double surge protection of the active components: Coarse protection by gas discharge tubes with 60V firing voltage with max. pulse leakage current 1kA (8/20µs) with additional integrated ESD fine protection of max. 2kV. Standard delivery with Power unit CPI1500DP (external power supply and USB-operation possible) IP3:>typ. +30dBm IP2:>typ. +50dBm Integrated double overvoltage protection of the active antenna part Integrated double surge protection of the active components: Coarse protection by gas discharge tubes with 60V firing voltage with max. pulse leakage current 1kA (8/20µs) with additional integrated ESD fine protection of max. 2kV. Fernando from Fenu-Radio.ch did the first comparison Test in Mai 2015 and released this test on his Page in German: www.fenu-radio.ch. Quote from the review by FenuRadio: (translated) "The NTi MegActiv is a small receiving antenna with excellent reception performance. The construction proved to be unproblematic, similar to the Boni-Whip. From VLF up on the FM band, the MegActiv receives very well despite their small size. When properly setup it provides a nearly unbeatable signal / noise ratio!" Whats in the box? MegActiv MA305FT Whip / Radiator Junction box CPI1500UNI Made in Germany Please note! The offered coax cables are custom-made and therefore not returnable / refundable.

CCMC50 Common Mode Noise Filter   Noise filters are nothing new and are often used for transmitting purposes. They are used to prevent unwanted radiation via the coax shielding. It is less known that they can also suppress unwanted radiation when receiving signals, especially when an active antenna is used. However, in this case, the situation is reversed: en route to the antenna, unwanted interferences from electric home appliances can be effectively eliminated.   This Coaxial Common Mode Choke (CCMC50) has been especially optimized for maximum common mode noise rejection of >30dB wide band in the frequency range of 500kHz – 50MHz. With slight limitations a much wider frequency range is covered. This is possible by using a cascaded system of ferrite cores with various frequency dependent material properties, combined with high quality PTFE coaxial cable. We recommend to connect the CCMC50 as closely as possible to the receiver.   For the highest demands we still offer the proven Common Mode Noise Filter CCMC30, which is specially optimized for maximum Common mode noise rejection of guaranteed> 30dB broadband in the reception range from 150kHz - 30MHz.   With the CCMC50 a reasonably priced version is now available with the following minor limitations against the CCMC30:   Common mode noise rejection guaranteed> 30dB, broadband in the reception range from 500kHz - 50MHz instead of starting at 150kHz. Starting with the medium wave over short wave up to the 6m amateur radio band, which should be sufficient for most applications. Not suitable for outdoor use because it is not splashproof.   With regard to efficient noise suppression, the CCMC50 is not very much different from the galvanic isolator GI1000. However, the CCMC50 performes down to lowest frequencies including DC voltage, in contrast to the GI1000, which blocks DC voltages and very low frequencies. The CCMC50 can thus be connected directly to the coax cable which passes the supply voltage or the control signals to the active antenna. A series connection of the GI1000 directly connected to the receiver followed by the CCMC50 right behind the power inserter may result in an even better performance. Technical Data Optimal frequency range: 500 kHz – 50 MHz Common Mode Wave suppression: >30 dB: 500 kHz -50MHz (>20 dB: 100kHz-70MHz) Insertion loss: <1 dB max. 500MHz, < 1.5dB bis max 1.5GHz Size: 127x65x43mm (160mm with BNC connectors) Connectors: 2x BNC 50Ohm Weight: 160g Made in Germany Absolutely not for transmitting purposes!

The MegaLoop FX active receiving loop with 3-way adjustable gain is now available in a new loop version: In addition to the optional large loops with 5-15m circumference and the 80cm diameter aluminum ring radiator, a 90cm diameter ring radiator variant is now available.The loop radiator is constructed of 20mm diameter stainless steel tubing that can be disassembled into eight plug-in segments to save space during transportation.For long-lasting use, it comes complete with a UV-resistant polycarbonate weatherproof enclosure and mast brackets (28 or 40 mm diameter), as well as all stainless steel mounting parts.A continuous pole, preferably metal and grounded, is required for mechanically stable mounting. It is attached twice, at the base and at the top, using appropriate pole brackets or clamps.Scope of delivery Loopring 90cm stainless steel, dismountable Weather protection enclousure2x pole brackets for top and bottomMast bracketStainless steel earthing cable The mast shown in the pictures and the MegaLoop are not included in the scope of delivery!

 Paloran 200 passive Loopantenne Ultra-breitbandiger Frequenzbereich von 9kHz bis 200MHz Unterschiedliche Strahlerformen und Größen verwendbar Im Innen- und Außenbereich verwendbar Zusätzlicher Erdungsanschluss (M5) am Gehäuse Hochwertig verarbeitet; spritzwassergeschütztes Gehäuse, alle Schraubanschlüsse in Edelstahl ausgeführt Kleine Verpackung = günstige Versandkosten Die PALORAN 200 ist eine hochwertige, breitbandig angepasste, passive Loopantenne. Die Paloran stellt eine gute Alternative überall dort dar, wo genügend Platz zur Aufhängung vorhanden ist und gleichzeitig störungsarmer Empfang benötigt wird. Loopantennen sprechen im Nahfeldbereich (Abstand weniger als ca. 3 Wellenlängen) hauptsächlich auf die magnetische (H-Feld) Komponente des elektromagnetischen Feldes an. Dadurch wird der Empfang von hauptsächlich elektrischen (E-Feld) Störungen im Nahfeld stark unterdrückt, was sich besonders im unteren Frequenzbereich (VLF/Langwelle/Mittelwelle und unterem KW-Bereich) durch störungsärmeren Empfang positiv bemerkbar macht. Durch die rein passive Wirkungsweise benötigt die PALORAN 200 (aufgrund der höheren Schleifenlängen ab 15m Umfang) einen größeren Platzbedarf im Vergleich zu einer aktiven Loopantenne. Dafür erzeugt die Antenne aber keinerlei Intermodulationen oder andere intern generierte Störkomponenten, ebenso entfällt die Fernspeisung. Lieferumfang: Paloran 200 15 Meter Großschleife aus PVC-ummantelten, seewasserfestem Edelstahldrahtseil (V4A) 2 Stück Isolatoren Manual Was brauche ich sonst noch? Die Paloran 200 wird ohne Koaxialkabel ausgeliefert, da ja jeder eine andere Länge benötigt. Wir bieten Ihnen dazu die passenden Kabel wie das HF214UF oder Hyperflex 5 in unterschiedlichen Längen an. Sie benötigen zwei Koaxkabel: Ein Koaxkabel zwischen der MegaDipol MD300DX Aktivdipol und der Einspeiseweiche CPI1000DP mit BNC-Steckern. Dazu ein weiteres Koaxialkabel, von der Einspeiseweiche (BNC-Stecker) zu ihrem Empfänger. In Meeresnähe oder beim möglichen Kontakt mit Salzwasser, empfehlen wir dringend den Einsatz unseres Wetterschutzgehäuses. Der Überspannungsableiter OVP1000 kann bei den aktuellen Wettereignissen ebenfalls sinnvoll sein. Zum Schutz der BNC-Stecker gegen Witterungseinflüsse, bieten wir mit dem NittoTape ein selbstvulkanisierendes Klebeband an.

GigActiv GA3005 Extreme Wideband Active Antenna Frequency range : 9 kHz - 3 GHz Power Supply: 5,5V - 12V Gain: + 3dB Upper Frequency Limit (-1db): 3000 MHz IP3: > +30 dBm typ. IP2: > +50 dBm typ. Where space is at a premium or you live in an area where an antenna is considered an undesirable element in neighborhood, the new GigActiv GA3005 is the ideal solution for the avid listener with a wide band receiver. The low noise GigActiv 3005 Extreme Wideband Active Antenna by NTi covers the whole frequency range from 9 kHz – 3 GHz. The antenna radiator measures only 10 cm (approx 4 inches) and so the unit can be mounted unobtrusively. The antenna requires a supply voltage of  5 –12V DC  (max. 120mA) fed through the coax cable via the standard supplied  DC interface CPI3000DP. It can also be powered via USB with slightly reduced performance. This is perfect for portable use in combination with a PC, which powers the antenna or the antenna can be powered autonomously and noise-free with a separate USB power bank. For shortwave and above 200MHz an IP3 of  typically > +30dBm is achieved. USB-powering possibleLarge supply voltage range of 5-12V. It can be powered either by a conventional plug power supply (5,5 / 2,1mm round plug) or via USB with a optional Cable. Autonomously and noise- free via a separate USB Power Bank as well. Whats in the Box?- GigActiv GA3005- Radiator- Junctionbox CPI3000UNI Dimesions incl Radiator:185 x 57 x 35mm  (7.28 x 2,24 x 1,38 inch) Made in Germany

HP0020 High Pass Filter The elliptically-formed high pass filter HP0020 suppresses all frequencies below 2 MHz.  Strong or near-by transmitters in the long- or medium wave range can cause interferences and intermodulation in the shortwave range, which can effectively be suppressed with this filter.  The HP0020 filter is very steep, so that signals in the upper medium wave range are already suppressed effectively. For the greatest possible effectiveness, the low pass filter  should be inserted directly before the receiver input.  Attenuation values (typ.):<0.50 MHz:-55dB1.0MHz: -45dB1.6 MHz:-35dB2.0MHz: -3dB>2.5 MHz: -1dB Input and output are DC-blocked (max. 50V DC) Dimensons: 88mmx31mmx25mm (3,46 x 1,22 x 0,98 inch) Attention: Only suitable for reception, high HF (>10dbm) will cause permanent damage! Because the filter is DC-blocked, it has to be inserted between the receiver input and the power inserter. Successfully tested with: Elad FDM-S1 and FDM-S2, FiFi-SDR1.0 and 2.0, PM-SDR, Winradio Excalibur, RFSpace SDR-IQ

OMG ?! This antenna will amaze you! The MegaDipole 300DX is a broadband active dipole with a maximum upper working frequency of 300 MHz. The dipole reacts to the electrical component (E-Field) of the electromagnetic field and will deliver best results regarding signal strength and SNR (signal -to-noise-ratio) at locations with little or no locally generated interference. Nonetheless, the receiver to be coupled to this antenna should have a high enough dynamic range so that it can effectively process the received signals. In contrast to simple E-field antennas with only one radiating element, the symmetrical construction of the MegaDipole 300DX, will result in almost no negative resonance effects or reflections caused by the coaxial cable. First choice for DXer The MegaDipol MD300DX is the ideal antenna for DXers. Particularly in electrically quiet environments, it can really play to its strength in efficiently amplifying weak signals. In practical operations, a maximum signal-to-noise ratio of 110dB was achieved! (see image ) Wideband With prodigious broadband capability and constant receive characteristics the MegaDipol MD300DX is ideal for wideband receivers, SDR's and WEB-SDR such as KiwiSDR etc. The MegaDipol MD300DX can of course also be operated on all other receivers, including lower-end SDRs and portable world receivers. Flexible power supply The MegaDipol is nominally supplied with 10 - 15V DC (max 40mA), however, it can be operated across a wide variety of supply voltages. The antenna can even be operated with slightly reduced IP values at the same gain with only 5 volts via USB. This offers a significant advantage in that you can supply the MegaDipol on trips away from the radio shack or DX expeditions autonomously, using a low-noise USB power-bank. "The MegaDipol has already attracted a lot of attention with its receive performance at various events such as DX-Camps, field days and in-house exhibitions. In these tests, the MD300DX surpassed the existing antennas usually by 10-15dB in the SNR." You want to test the MegaDipol MD300DX live on air? If you would like to test the MegaDipol MD300DX live, you can now conveniently do this over the Internet with a KIWI SDR. Just click on this Link and you can browse the whole band from 10kHz to 30MHz. The linked KIWI-SDR with a vertical MegaDipol MD300DX is in Ireland and can handle up to 4 users at a time. Customer Feedback"MegaDipol has arrived and installed. It seems to be a great antenna, especially compared to dimensions!" Technical data Frequency range: 9kHz - 300MHz IP3: typ. +30dBm (@7.00 & 7.20MHz) IP2: typ. +78dBm (@7.00 & 7.20MHz) Size/weight: 98 x 90 x 38mm / 0.12kg Whats in the Box? MegaDipol MD300DX Power Inserter CPI 1500UNI 2x 2.5m long radiating elements (PVC-coated, salt-water resistant stainless steel ropes) 2 insulators for installation (weatherproof plastic material with 4.5mm fixing hole) As noted previously, it is important that the connected receiver has a correspondingly high dynamic range in order to be able to optimally process the delivered signals. Recommendation Near the sea or in case of possible contact with salt water we strongly recommend the use of our weather protection case. Please note! The offered coax cables are custom-made and therefore not returnable / refundable.

Langlebiges Wetterschutzgehäuse für aktive AntennenDieses Wetterschutzgehäuse wurde speziell zum dauerhaften Schutz aktiver NTi Monopol-Antennen wie MegActiv MA305, GigActiv und Boni-Whip entwickelt. Das robuste, weitgehend UV-beständige Gehäuse aus Polycarbonat, schützt die Antennenelektronik zuverlässig vor Regen, Schmutz und mechanischen Einflüssen. Der transparente Deckel ermöglicht eine einfache Sichtprüfung der Antennenköpfe, ohne das Gehäuse öffnen zu müssen. Durch das bewährte Gehäuse-im-Gehäuse-Prinzip wird die empfindliche Elektronik zusätzlich isoliert und geschützt. Ein zusätzlicher externer Erdungsanschluss an der antennenseitigen Masseverbindung der BNC-Anschlussbuchse gewährleistet eine sichere und fachgerechte Erdung.Zur Vermeidung von Kondenswasser ist das Wetterschutzgehäuse nach unten offen bzw. belüftet, wodurch Feuchtigkeit zuverlässig abgeführt wird. Sämtliche Befestigungselemente aus Edelstahl garantieren Korrosionsbeständigkeit und eine hohe mechanische Stabilität – selbst bei langfristigem Einsatz im Freien.Ideal für langlebige und wartungsarme Antenneninstallationen im Outdoor-Bereich.Einfache und sichere MastbefestigungDas Wetterschutzgehäuse ist bereits für die optional erhältliche Masthalteplatte (Art.-Nr. 0127) vorbereitet und ermöglicht so eine einfache und sichere Mastmontage. Bereits vorhandene Masthalterungen können selbstverständlich weiterverwendet werden. Lieferumfang1x vormontiertes Wetterschutzgehäuse mit Trägerplatte incl. Erdanschlussverbinder zur BNC-Buchse1x Strahleranschluss-Schraube 25mm lang & Karosseriescheibe (M5 oder M6) Montageanleitung Eine Montageanleitung finden Sie hier: Montageanleitung PDFInformationen gemäß Art. 19 GPSR Adresse des Herstellers:  Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net Adresse der verantwortlichen Person: Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net

ALLMOPRAN 120 – Passive Allmode Receiving Antenna 20 kHz – 120 MHz Extremely wideband frequency range from 20 kHz to 120 MHz Compatible with different radiator types and sizes Inputs and output protected by fast 70V gas discharge arrestors Switchable input-side limiter (2 Vpp) Additional grounding terminal (M5) on the housing High-quality workmanship; splash-proof housing, all screw connections made of stainless steel Universal radiator set included: 2 × 7.5 m PVC-coated stainless steel wire rope Compact packaging = low shipping costs Universally configurable The ALLMOPRAN 120 from NTi is an innovative passive receiving antenna for demanding applications and a true all-rounder. It can be configured for connection with the following radiator types: Dipole (balanced) or End-fed (unbalanced) Loop (balanced or single-ended grounded) The ALLMOPRAN can therefore be configured for either H-mode or E-mode operation. Switching is done via a toggle switch, provided that the corresponding type of radiator is connected. The standard delivery includes a 2 × 7.5 m universal radiator set, allowing for a wide range of different radiator configurations. By combining high-quality transformer materials with a wideband matching network, operation is also possible in the VLF range – typically a weak spot for passive antennas. As a passive system, no additional power supply is required. The BNC connector socket is splash-proof and mounted in a durable, UV-stabilized polycarbonate housing with a transparent cover. Flexible adaptation to the local interference environment Electromagnetic waves consist of two different components in the near field: H or B (magnetic field strength vector) E (electric field strength vector) The near field is defined as a maximum distance of one wavelength; beyond that, far-field conditions apply. While the two field strength vectors are 90° out of phase in the near field, they are no longer separated in the far field. Since most sources of interference are found below 3 MHz, near-field conditions already apply at distances of less than 100 m. In such cases, it can make sense to prefer or suppress the E- or H-component in the near field. Depending on local conditions and interference sources, one or the other field component may provide better reception results. Want to test the ALLMOPRAN 120 live? You can now conveniently test the ALLMOPRAN 120 live on the Internet via a WEB-SDR. Simply click [this link], and you can explore the entire band from 20 kHz to 30 MHz. The linked WEB 888-SDR with the ALLMOPRAN in End-Fed mode and a total length of 21 m is located in Alsace (France). Up to 4 users can access it simultaneously. TECHNICAL DATA Optimal frequency range: 20 kHz – 120 MHz (–3 dB) Connector type & impedance: BNC / 50 Ohm Radiator connections: M5 thread (stainless steel) Output is DC-blocked (max. 50 V) Operating temperature range: –25°C to +45°C Size/weight: 105 × 105 × 50 mm / 0.2 kg Weather protection housing: splash-proof according to IPX2 (protected against dripping water at up to 15° tilt) Scope of delivery: ALLMOPRAN 120 in splash-proof weather housing Universal radiator set 2 × 7.5 m PVC-coated stainless steel wire rope Optional accessories: Mast mounting bracket Ground connection cable 155 mm, stainless steel wire rope, M5/M6 Manual (latest version available for download) FAQ The FAQ for the ALLMOPRAN can be downloaded [here].