PL-Connector UHF-Special/6 This high-quality PL-259 connector is suitable for the coax cable types: RG58U, RG58CU, RG142B/U, RG223U, RG400U, Aircell 5, Airborne 5, H 155, H 2005 und Hyperflex 5. It is equipped as standard with two ground connection sleeves for RG58 and the thicker H 155, Hyperflex 5 etc. Type: UHF connector special Design: Connector Connection: Soldering Cable inlet Ø6 mm We use these connectors for the prefabricated H155 and Hyperflex 5 coax cables. The assembly instructions can be downloaded here or under the "Media" tab.
BNC special connector for 4.8mm - 5.5mm coaxial cable This BNC connector is suitable for soldering H155 Hyperflex 5, Aircell 5 and RG58 coax cable. It has a nikel-plated plug housing, PTFE dielectric and gold-plated center contact. Also included is a piece of scraping tubing.
UHF PL 259 connector for 5 to 6 mm coaxial cables such as RG58, Airborn 5, Aircel 5, H155, Hyperflex 5, HF214, with PTFE insulation and gold-plated center contact. Assembly: The connector is assembled according to the well-known "twist-on principle" by unscrewing and soldering the center contact.
PL-connector PL7 for Ultraflex 7 This high-quality PL-259 connector is suitable for the coax cable types H 2007, H 2007 FRNC, HIGHFLEXX 7, Aircell 7 and of course Ultraflex 7. It is equipped as standard with a ground connection sleeve. Type: UHF connector specialDesign: ConnectorConnection: SolderingCable inlet Ø7.3 mm We use these connectors for the prefabricated Ultraflex 7 coax cables. The assembly instructions can be downloaded here
BNC connector crimp version for H155 and Hyperflex 5 coaxial cable This BNC connector is suitable for crimping to H155, Hyperflex 5, Aircell 5, Airborne 5 etc cable. It has a silver-plated plug housing, PTFE dielectric and a gold-plated center contact. Also included is a piece of scraping tubing.
Original Messi&Paoloni UHF Stecker PL259 - EVO 5,4mm Die beliebten NEO bzw. EVO PL-Stecker sind nun endlich auch für 5,4mm Koaxkabel Hyperflex 5, Hyperflex 5 Crystal, H155 und HF 214 erhältlich. Warum sollten Sie diesen Stecker verwenden? Kompressionsdesign mit doppelter Dichtung, die einen besseren Schutz gegen das Eindringen von Wasser, Feuchtigkeit und Kondensation gewährleistet. Einfache Installation (kein Löten des Geflechts erforderlich). Drastische Unterdrückung des Hintergrundrauschens, Verbesserung der Schirmdämpfung und der Einfügungsverluste. Der neu gestaltete Stift verhindert einen Zinnüberschuss und die daraus resultierende Erwärmung, die das Dielektrikum beschädigt und zu einer unkontrollierbaren Veränderung der elektrischen Eigenschaften Ihres Kabels führt (anders als beim Standard-PL259, der einer starken thermischen Belastung ausgesetzt ist). Bei herkömmlichen UHF (PL259) HF-Steckverbindern mit Gewinde ist es notwendig, den Mittelleiterstift mit geschmolzenem Lot zu füllen. Der abgerundete Stift von Evo beseitigt das Problem der Lötgrate. Eine ausgeklügelte Bearbeitung verbessert die Öffnung des Steckerbodens und erleichtert das Einführen des Kabelleiters. Der neue UHF Evolution kann bequem bis 6000 MHz eingesetzt werden, ein gut gemachter PL259 ist bis 2000 MHz gerade noch akzeptabel. Noch nie kam ein PL in Bezug auf Leistung und Zuverlässigkeit so nah an die berühmten "N"-Stecker heran. Nur geeignet für folgende Kabeltypen: Hyperflex 5 Hyperflex 5 Crystal H155 HF 214 Zur Videoanleitung Herstellernummer: CO.UHF.54M-S EVO Informationen gemäß Art. 19 GPSRHersteller: Messi&PaoloniHerstellername: Messi & Paoloni SrlHandelsname: Messi & PaoloniAdresse: Via Giovanni Conti 1 - 60131 ANCONA, ItalyE-Mail: web@messi.itWebseite: https://messi.it/ Verantwortliche Person:Name: Messi & Paoloni SrlAdresse: Via Giovanni Conti 1 - 60131 ANCONA, ItalyE-Mail: web@messi.itWebseite: https://messi.it/
UHF PL-259 connector twist 7mm UHF PL 259 plug for 7 mm coaxial cables such as RF-287 UF, Highflexx 7, Aircell 7. H 2007, Ultraflex 7, LMR 300 and similar. with PTFE insulation and gold-plated center contact. Assembly: The plug is assembled according to the well-known "twist-on principle" by unscrewing and soldering the center contact.
The HF 300 PVC is a professional 50 Ohm coaxial cable manufactured by the renowned Italian cable specialist Siva Cavi. With an outer diameter of 7.6 mm, it belongs to the class of compact yet powerful low-loss cables, designed for amateur radio, CB, VHF/UHF, repeater stations, antenna systems and measurement technology. Thanks to its innovative skin-foam-skin dielectric combined with a double shielding system (bonded AL-PET-AL foil + 82% tinned copper braid), the HF 300 PVC provides exceptional shielding effectiveness of more than 100 dB and ensures low attenuation per 100 meters. This makes it a reliable solution both for short patch cables and long transmission lines. Technical Specifications Manufacturer: Siva Cavi (Italy) Impedance: 50 Ohm Outer diameter: 7.6 mm Inner conductor: solid copper, Ø 1.78 mm Dielectric: Skin-Foam-Skin PE, Ø 4.85 mm Shielding: AL-PET-AL bonded foil + 82% tinned copper braid Shielding effectiveness: >100 dB (100–900 MHz) Outer jacket: durable black PVC, UV resistant Attenuation @ 100 MHz: ~3.0 dB / 100 m Attenuation @ 1000 MHz: ~20.0 dB / 100 m Operating temperature: –30 °C to +70 °C Key Benefits Premium quality by Siva Cavi – Made in Italy Compact 7.6 mm diameter – flexible and easy to install Very high shielding for interference-free signal transmission Low attenuation even at higher frequencies Universal use for radio, antenna, SAT and measurement applicationsInformationen gemäß Art. 19 GPSR SI.VA SRL - Via Vittorio Veneto, 63 - 24040 Bonate Sotto (Bergamo) Italy Tel. 035 991085/86 - siva@sivacavi.it - https://sivacavi.it/ Verantwortliche Person: SI.VA SRL - Via Vittorio Veneto, 63 - 24040 Bonate Sotto (Bergamo) Italy Tel. 035 991085/86 - siva@sivacavi.it - https://sivacavi.it/
PL-connector UHF-Special 10 This high-quality PL-259 connector is suitable for the coax cable types: HyperFlex 10, H 2010, H 2010 FRNC = Calorix 10, Ecoflex 10, Ultraflex 10,H2000 Flex, H 1000, LMR 400, MMR 400, Neoflex 10. Type: UHF connector special Design: Connector Connection: Soldering Cable inlet Ø10,3 mm Material: Housing: nickel-plated brass. Dielectric: Teflon (PTFE) We use these connectors for the prefabricated Hyperflex 10 coax cables. The assembly instructions can be downloaded here or under the "Media" tab.
N-connector for Ultraflex 7 This high-quality N connector is suitable for the coax cable types H 2007, H 2007 FRNC, HIGHFLEXX 7, Aircell 7 and of course Ultraflex 7. It is equipped as standard with a ground connection sleeve. Type: UHF connector special Design: Connector Connection: Soldering Cable inlet Ø7.3 mm We use these connectors for the prefabricated Ultraflex 7 coax cables.
Solder ''PL / UHF'' female connector 5-6mm This high-quality PL-259 socket is suitable for the coaxial cable types: RG58U, RG58CU, RG142B / U, RG223U, RG400U, Aircell 5, Airborne 5, H 155, H 2005 and Hyperflex 5. It is supplied as standard with a ground connection sleeve each for RG58 and the somewhat thicker cable types. Type: UHF connector special Version: socketConnection: solder versionCable inlet Ø6.0 mm The assembly instructions are available for download here
N-Connector special 5-6 mm This high-quality N connector is suitable for the coax cable types: RG58U, RG58CU, RG142B/U, RG223U, RG400U, Aircell 5, Airborne 5, H 155, H 2005 und Hyperflex 5. It is equipped as standard with two ground connection sleeves for RG58 and the thicker H 155, Hyperflex 5 etc. Type: N connector special Design: Connector Connection: Soldering Cable inlet Ø6 mm
N-Connector special 10 mm This high-quality N connector is suitable for the coax cable types: HyperFlex 10, H 2010, H 2010 FRNC = Calorix 10, Ecoflex 10, Ultraflex 10,H2000 Flex, H 1000, LMR 400, MMR 400, Neoflex 10. The center pins are provided with two different holes (solder contacts) The center pin with the bigger solder contact has the right dimension for Ultraflex 10, H 2010, Calorix 10, HyperFlex 10, Ecoflex 10, RG 213 LOW LOSS and similar cables. The center pin with the smaller solder contact has the right dimension for H 2000 Flex, H 1000, Aircom Premium Type: N connector special Design: Connector Connection: Soldering Cable inlet Ø10,3 mm The assembly instructions can be downloaded here or under the "Media" tab.
The problem solver for 7mm Coax cables Difficult position of the PL /UHF socket on the device which can only be solved with an adapter, but then this adapter is too long? Why not mount a right angle connector on the cable? This high-quality PL / UHF Right Angle 90° RF Connector for 7mm is suitable for coaxial cable types: Ultraflex 7, Ultraflex 7 Crystal, Highflex 7 or Aircell 7and Hyperflex 5. It comes with one grounding connection sleeve. Quality you feel and hear You will immediately notice the high weight. This is because this adapter is made of nickel-plated brass in industrial quality. The PTFE dielectric ensures lowest insertion loss and a quiet frequency response. Type: PL/UHF angle connector Version: 90 degree angle connector Material: Housing: nickel-plated brass. Dielectric: PTFE Connection: solder version Cable inlet Ø7,8 mm We can fabricate these connectors for the prefabricated Ultraflex 7, Ultraflex 7 Crystal or Highflexx 7 coaxial cables.
The problem solver Difficult position of the PL / UHF socket on the device (for example in the car) which can only be solved with an adapter, but then this adapter is too long? Why not mount a right angle connector on the cable? This high-quality PL/UHF right Angle 90° RF connector is suitable for 5mm coaxial cable types: RG58U, RG58CU, RG142B / U, RG223U, RG400U, Aircell 5, Airborne 5, H 155, H 2005 and Hyperflex 5. It comes standard with one grounding sleeve for RG58 and another sleeve for the slightly thicker cable types like H155 etc. Quality you feel and hear You will immediately notice the high weight. This is because this adapter is made of nickel-plated brass in industrial quality. The PTFE dielectric ensures lowest insertion loss and a quiet frequency response. Type: PL/UHF angle connector Version: 90 degree angle connector Material: Housing: nickel-plated brass. Dielectric: PTFE Connection: solder version Cable inlet Ø6,0 mm We can fabricate these connectors for the prefabricated H 155 and Hyperflex 5 and RG58 coaxial cables.
Solder ''PL / UHF'' female connector for 7mm coaxial cables This high-quality PL-259 socket is suitable for the coaxial cable types: Aircell 7, Ultraflex 7, HIGHFLEXX 7 etc. It is delivered with a ground connection sleeve as standard. Type: UHF connector special Version: socketConnection: solder versionCable inlet Ø7.4 mm
SMA connector crimpThese SMA connectors are suitable for crimping onto H155, Hyperflex 5, Aircell 5 and Airborne 5 coaxial cables. It has a PTFE dielectric and a gold plated center contact and case.
The EVO series connectors from Messi&Paoloni are perfect for 7,3mm diameter coaxial cables such as Ultraflex 7, Ultraflex 7PE or the new POTA-FLEX 7. The installation of these connectors is straightforward and is supported by helpful instructions on the packaging and clear videos. Thanks to their clever design with double sealing, the connectors offer excellent protection against water, moisture and condensation. Superior quality Made in Italy. Why choose this connector? Genuine Messi & Paoloni enhanced solder connector UHF Male (PL259) 2-Pack Compression design with double seal to ensure better protection against infiltration of water, humidity and condensation Easy installation and welding instructions included in the package (no braid soldering needed) Dramatic suppression of the background noise, improvement of screening attenuation and insertion losses The UHF Evolution can be used up to 6000 MHz, a well made PL259 is barely acceptable up to 2000 MHz Model MP-CO.UHF.7M-S-EVO Product dimensions: 0.82 x 1.81 in. (2.1cm x 4.6cm) Wrench size: 0.63 in (16mm) For ULTRAFLEX 7 /.287'' cable Note: The new designed pin prevents excess of tin and the consequent heating, which damages the dielectric causing an uncontrollable alteration of the electrical properties of your cable.
BNC-connector (plug) for 7 mm coax cables This BNC connector is suitable for soldering to Ultraflex 7, HIGHFLEXX 7, Aircell 7 cable. It has a nikel-plated plug housing, PTFE dielectric and a gold-plated center contact. Also included is a piece of scraping tubing.
UHF-Kabelbuchse für RG 213 U, RG 214 U, H 2000 Flex, H 1000, LMR 400, Aircom P, Ecoflex 10, Heatex 10, MMR 400, H 2010, Ultraflex 10, Calorix 10, HyperFlex 10 u.ä.
The problem solver Difficult position of the BNC socket on the device (for example in the car) which can only be solved with an adapter, but then this adapter is too long? Why not mount a right angle connector on the cable? This high-quality BNC angle plug is suitable for coaxial cable types: RG58U, RG58CU, RG142B / U, RG223U, RG400U, Aircell 5, Airborne 5, H 155, H 2005 and Hyperflex 5. It comes standard with one earth connection sleeve for RG58 and another sleeve for the slightly thicker cable types. Type: BNC angle connector Version: 90 degree angle connectorConnection: solder versionCable inlet Ø6,0 mm We use these connectors for the prefabricated H 155 and Hyperflex 5 and RG58 coaxial cables. Assembly instructions
Original Messi & Paoloni N-Stecker - EVO 5,4mmDieser hochwertige N-Stecker von Messi & Paoloni ist für die Koaxkabeltypen: Hyperflex 5, Hyperflex 5 Crystal, HF-214, H155, u.ä. mit einem Durchmesser von 5,4mm geeignet. Der Löt-N-Stecker kommt mit Dichtungsring, PTFE-Dielektrikum und vergoldetem Mittelstift zu Ihnen. Die zwei mitgelieferten PTFE-Scheiben ermöglichen eine einfache Installation des Steckers. Die PTFE-Scheiben und eine ringförmige Verdickung auf dem Mittelkontakt verhindern, dass das Kabel bei mechanischer Belastung aus der festgelegten Position gezogen werden kann.Kompressionsdesign mit doppelter Dichtung, die einen besseren Schutz gegen das Eindringen von Wasser, Feuchtigkeit und Kondenswasser gewährleistet.Einfache Installation und Lötanleitung im Paket enthalten (kein Lötgeflecht erforderlich). Drastische Unterdrückung des Hintergrundrauschens, Verbesserung der Schirmdämpfung und der Einfügungsverluste. Die Oberflächen sind mit einer speziellen Legierung namens Smart3-Alloy® behandelt: Sie ist korrosionsbeständig und antiallergisch. Der neu konzipierte Stift verhindert einen Zinnüberschuss und die daraus resultierende Erwärmung, die das Dielektrikum beschädigt und zu einer unkontrollierbaren Veränderung der elektrischen Eigenschaften Ihres Kabels führt. Messi & Paoloni Code: CO.N.54M-S Informationen gemäß Art. 19 GPSRHersteller: Messi&PaoloniHerstellername: Messi & Paoloni SrlHandelsname: Messi & PaoloniAdresse: Via Giovanni Conti 1 - 60131 ANCONA, ItalyE-Mail: web@messi.itWebseite: https://messi.it/Verantwortliche Person:Name: Messi & Paoloni SrlAdresse: Via Giovanni Conti 1 - 60131 ANCONA, ItalyE-Mail: web@messi.itWebseite: https://messi.it/
N socket connector 5-6mm Our 50 Ohm solder N socket with sealing ring, PTFE dielectric, gold-plated center pin. Available for cables with 5-6mm (H155, Hyperflex 5, Aircell 5). Our N cable socket is suitable for all cables of RG 58 dimensions (RG58, Aircell 5, Airborn 5 etc.) as well as for all cable types with 5.4mm of the H 155, Hyperflex 5. This N socket is provided with 2 ground connection sleeves and 2 center pins. The sleeve with the larger receptacle is designed for H 155 and similar cables. The same applies to the center contact with the larger solder hole. The center contacts are diamagnetic. Usable for:RG 58 CU, H 155, Hyperflex 5, Aircell 5, Airborne 5, H 2005, RG 223 U, RG 400 U, RG 142 BU and similar
N-Stecker Crimp Dieser N-Stecker ist zum Krimpen auf H155, Hyperflex 5, Aircell 5 & Airborne 5 Koaxialkabel geeignet. Mit PTFE-Dielektrikum und vergoldetem Mittelkontakt.
Messi & Paoloni N-connector for 7mm coaxial cable This high-quality N-connector from Messi & Paoloni is suitable for coaxial cable types: Ultraflex 7, PotaFlex 7, H 2007, HIGHFLEXX 7, Aircell 7 and similar. The solder N connector comes with a sealing ring, PTFE dielectric and gold-plated center pin. The two PTFE washers supplied make it easy to install the connector. The PTFE washers and a ring-shaped thickening on the center contact prevent the cable from being pulled out of its fixed position under mechanical stress.Compression design with double seal that ensures better protection against infiltration of water, humidity and condensation.Easy installation and welding instructions included in the package (no braid soldering needed).Dramatic suppression of the background noise, improvement of screening attenuation and insertion losses.The surfaces are treated with a special alloy called Smart3-Alloy®: it is corrosion-resistant and hypoallergenic.The new designed pin prevents excess of tin and the consequent heating, which damages the dielectric causing an uncontrollable alteration of the electrical properties of your cable (differently from standard PL259 which is exposed to strong thermical stress). Product dimensions: 2,1cm x 4,0cm Wrench size: 16mm (0,63 in) *Connectors are sold individually, image is for illustrative purpose. Code: CO.N.7M-S
With this practical metal cap, you can easily protect your N or PL connectors from moisture. It is equipped with a 9 cm long chain and an eyelet for attachment. This ensures that exposed connectors always remain dry and protected. Weight approx. 23 g.
Original Messi&Paoloni UHF Stecker PL259 - EVO 6mm Messi&Paoloni UHF/PL259 Stecker EVO für 6mm Potaflex 6 Koaxkabel. Warum sollten Sie diesen Stecker verwenden? Kompressionsdesign mit doppelter Dichtung, die einen besseren Schutz gegen das Eindringen von Wasser, Feuchtigkeit und Kondensation gewährleistet. Einfache Installation und eine Anleitung zum Löten sind in der Verpackung enthalten (kein Löten des Geflechts erforderlich). Drastische Unterdrückung des Hintergrundrauschens, Verbesserung der Schirmdämpfung und der Einfügungsverluste. Der neu gestaltete Stift verhindert einen Zinnüberschuss und die daraus resultierende Erwärmung, die das Dielektrikum beschädigt und zu einer unkontrollierbaren Veränderung der elektrischen Eigenschaften Ihres Kabels führt (anders als beim Standard-PL259, der einer starken thermischen Belastung ausgesetzt ist). Bei herkömmlichen UHF (PL259) HF-Steckverbindern mit Gewinde ist es notwendig, den Mittelleiterstift mit geschmolzenem Lot zu füllen. Der abgerundete Stift von Evo beseitigt das Problem der Lötgrate. Eine ausgeklügelte Bearbeitung verbessert die Öffnung des Steckerbodens und erleichtert das Einführen des Kabelleiters. Der neue UHF Evolution kann bequem bis 6000 MHz eingesetzt werden, ein gut gemachter PL259 ist bis 2000 MHz gerade noch akzeptabel. Noch nie kam ein PL in Bezug auf Leistung und Zuverlässigkeit so nah an die berühmten "N"-Stecker heran. Nur geeignet für folgende Kabeltypen: PotaFlex 6 RG8X Zur Videoanleitung Herstellernummer: CO.UHF.6M-S EVO POTA
Messi & Paoloni N-Stecker für 10mm Koaxkabel Dieser hochwertige N-Stecker von Messi & Paoloni ist für die Koaxkabeltypen: Ultraflex 10, Hyperflex 10, Airborn 10, Ecoflex10, RG-213, H2000 geeignet. Der Löt-N-Stecker kommt mit Dichtungsring, PTFE-Dielektrikum und vergoldetem Mittelstift zu Ihnen. Die zwei diamagnetische Mittelstifte sind lötbar und lassen sich auf viele 10,3 mm-Kabel montieren. Die Mittelstifte sind mit verschieden großen Lötöffnungen versehen. Die zwei mitgelieferten PTFE-Scheiben ermöglichen eine einfache Installation des Steckers. Die PTFE-Scheiben und eine ringförmige Verdickung auf dem Mittelkontakt verhindern, dass das Kabel bei mechanischer Belastung aus der festgelegten Position gezogen werden kann. Kompressionsdesign mit doppelter Dichtung, die einen besseren Schutz gegen das Eindringen von Wasser, Feuchtigkeit und Kondenswasser gewährleistet. Einfache Installation und Lötanleitung im Paket enthalten (kein Lötgeflecht erforderlich). Drastische Unterdrückung des Hintergrundrauschens, Verbesserung der Schirmdämpfung und der Einfügungsverluste. Die Oberflächen sind mit einer speziellen Legierung namens Smart3-Alloy® behandelt: Sie ist korrosionsbeständig und antiallergisch. Der neu konzipierte Stift verhindert einen Zinnüberschuss und die daraus resultierende Erwärmung, die das Dielektrikum beschädigt und zu einer unkontrollierbaren Veränderung der elektrischen Eigenschaften Ihres Kabels führt. Messi & Paoloni Code: CO.N.10M-S Informationen gemäß Art. 19 GPSRHersteller: Messi&PaoloniHerstellername: Messi & Paoloni SrlHandelsname: Messi & PaoloniAdresse: Via Giovanni Conti 1 - 60131 ANCONA, ItalyE-Mail: web@messi.itWebseite: https://messi.it/ Verantwortliche Person:Name: Messi & Paoloni SrlAdresse: Via Giovanni Conti 1 - 60131 ANCONA, ItalyE-Mail: web@messi.itWebseite: https://messi.it/
With this practical metal cap, you can easily protect your N or PL female connectors from moisture. It is equipped with a 9 cm long chain and an eyelet for attachment. This ensures that open connectors always remain dry and protected. Weight approx. 23 g.
The problem solver Difficult position of the PL /UHF socket on the device which can only be solved with an adapter, but then this adapter is too long? Why not mount a right angle connector on the cable? This high-quality PL / UHF Right Angle 90° RF Connector for 10mm is suitable for coaxial cable types: Ultraflex 10, Hyperflex 10 etc. It comes with one grounding connection sleeve. Quality you feel and hear You will immediately notice the high weight. This is because this adapter is made of nickel-plated brass in industrial quality. The PTFE dielectric ensures lowest insertion loss and a quiet frequency response. Type: PL/UHF angle connector Version: 90 degree angle connector Material: Housing: nickel-plated brass. Dielectric: PTFE Connection: solder version Cable inlet Ø10,3 mm We can fabricate these connectors for the prefabricated Hyperflex 10 coaxial cables.