Filter products
PL-Connector UHF-Special/6 This high-quality PL-259 connector is suitable for the coax cable types: RG58U, RG58CU, RG142B/U, RG223U, RG400U, Aircell 5, Airborne 5, H 155, H 2005 und Hyperflex 5. It is equipped as standard with two ground connection sleeves for RG58 and the thicker H 155, Hyperflex 5 etc. Type: UHF connector special Design: Connector Connection: Soldering Cable inlet Ø6 mm We use these connectors for the prefabricated H155 and Hyperflex 5 coax cables. The assembly instructions can be downloaded here or under the "Media" tab.
Original Messi&Paoloni UHF Stecker PL259 - EVO 5,4mm Die beliebten NEO bzw. EVO PL-Stecker sind nun endlich auch für 5,4mm Koaxkabel Hyperflex 5, Hyperflex 5 Crystal, H155 und HF 214 erhältlich. Warum sollten Sie diesen Stecker verwenden? Kompressionsdesign mit doppelter Dichtung, die einen besseren Schutz gegen das Eindringen von Wasser, Feuchtigkeit und Kondensation gewährleistet. Einfache Installation (kein Löten des Geflechts erforderlich). Drastische Unterdrückung des Hintergrundrauschens, Verbesserung der Schirmdämpfung und der Einfügungsverluste. Der neu gestaltete Stift verhindert einen Zinnüberschuss und die daraus resultierende Erwärmung, die das Dielektrikum beschädigt und zu einer unkontrollierbaren Veränderung der elektrischen Eigenschaften Ihres Kabels führt (anders als beim Standard-PL259, der einer starken thermischen Belastung ausgesetzt ist). Bei herkömmlichen UHF (PL259) HF-Steckverbindern mit Gewinde ist es notwendig, den Mittelleiterstift mit geschmolzenem Lot zu füllen. Der abgerundete Stift von Evo beseitigt das Problem der Lötgrate. Eine ausgeklügelte Bearbeitung verbessert die Öffnung des Steckerbodens und erleichtert das Einführen des Kabelleiters. Der neue UHF Evolution kann bequem bis 6000 MHz eingesetzt werden, ein gut gemachter PL259 ist bis 2000 MHz gerade noch akzeptabel. Noch nie kam ein PL in Bezug auf Leistung und Zuverlässigkeit so nah an die berühmten "N"-Stecker heran. Nur geeignet für folgende Kabeltypen: Hyperflex 5 Hyperflex 5 Crystal H155 HF 214 Zur Videoanleitung Herstellernummer: CO.UHF.54M-S EVO Informationen gemäß Art. 19 GPSRHersteller: Messi&PaoloniHerstellername: Messi & Paoloni SrlHandelsname: Messi & PaoloniAdresse: Via Giovanni Conti 1 - 60131 ANCONA, ItalyE-Mail: web@messi.itWebseite: https://messi.it/ Verantwortliche Person:Name: Messi & Paoloni SrlAdresse: Via Giovanni Conti 1 - 60131 ANCONA, ItalyE-Mail: web@messi.itWebseite: https://messi.it/
Messi & Paoloni PL Connector CO.UHF.5M-S EVO – High-quality, low-loss UHF male connector for 5 mm coaxial cables. The CO.UHF.5M-S EVO is the latest generation of Messi & Paoloni’s renowned PL connectors, engineered for maximum conductivity and mechanical strength. With precision CNC machining, nickel-plated brass parts, and a solid strain relief system, this connector guarantees outstanding RF performance and easy installation. Perfectly matched for coaxial cables such as RG-58, Airborne 5, HF195, Aircell 5, or similar 5 mm cables. Thanks to the EVO series design, it ensures improved contact transition, minimal signal loss, and excellent corrosion resistance — ideal for amateur radio, CB radio, shortwave reception, and outdoor antenna setups. Technical Features: Type: PL connector (UHF male) Model: CO.UHF.5M-S EVO Fits 5 mm coaxial cables (e.g., RG-58, Airborne 5, Hyperflex 5) Material: Nickel-plated brass, PTFE insulator Solder type – robust and RF-tight EVO design for improved conductivity and strain relief Brand: Messi & Paoloni (Made in Italy) Conclusion: The CO.UHF.5M-S EVO is the perfect choice for radio amateurs and technicians who demand top signal quality and long-lasting connections. A professional-grade PL connector that combines performance and reliability — Made by Messi & Paoloni.Informationen gemäß Art. 19 GPSR Hersteller: Messi&Paoloni Herstellername: Messi & Paoloni Srl Handelsname: Messi & Paoloni Adresse: Via Giovanni Conti 1 - 60131 ANCONA, Italy E-Mail: web@messi.it Webseite: https://messi.it/ Verantwortliche Person: Name: Messi & Paoloni Srl Adresse: Via Giovanni Conti 1 - 60131 ANCONA, Italy E-Mail: web@messi.it Webseite: https://messi.it/
Solder ''PL / UHF'' female connector 5-6mm This high-quality PL-259 socket is suitable for the coaxial cable types: RG58U, RG58CU, RG142B / U, RG223U, RG400U, Aircell 5, Airborne 5, H 155, H 2005 and Hyperflex 5. It is supplied as standard with a ground connection sleeve each for RG58 and the somewhat thicker cable types. Type: UHF connector special Version: socketConnection: solder versionCable inlet Ø6.0 mm The assembly instructions are available for download here
The problem solver Difficult position of the PL / UHF socket on the device (for example in the car) which can only be solved with an adapter, but then this adapter is too long? Why not mount a right angle connector on the cable? This high-quality PL/UHF right Angle 90° RF connector is suitable for 5mm coaxial cable types: RG58U, RG58CU, RG142B / U, RG223U, RG400U, Aircell 5, Airborne 5, H 155, H 2005 and Hyperflex 5. It comes standard with one grounding sleeve for RG58 and another sleeve for the slightly thicker cable types like H155 etc. Quality you feel and hear You will immediately notice the high weight. This is because this adapter is made of nickel-plated brass in industrial quality. The PTFE dielectric ensures lowest insertion loss and a quiet frequency response. Type: PL/UHF angle connector Version: 90 degree angle connector Material: Housing: nickel-plated brass. Dielectric: PTFE Connection: solder version Cable inlet Ø6,0 mm We can fabricate these connectors for the prefabricated H 155 and Hyperflex 5 and RG58 coaxial cables.
BNC special connector for 4.8mm - 5.5mm coaxial cable This BNC connector is suitable for soldering H155 Hyperflex 5, Aircell 5 and RG58 coax cable. It has a nikel-plated plug housing, PTFE dielectric and gold-plated center contact. Also included is a piece of scraping tubing.
BNC connector crimp version for H155 and Hyperflex 5 coaxial cable This BNC connector is suitable for crimping to H155, Hyperflex 5, Aircell 5, Airborne 5 etc cable. It has a silver-plated plug housing, PTFE dielectric and a gold-plated center contact. Also included is a piece of scraping tubing.
The problem solver Difficult position of the BNC socket on the device (for example in the car) which can only be solved with an adapter, but then this adapter is too long? Why not mount a right angle connector on the cable? This high-quality BNC angle plug is suitable for coaxial cable types: RG58U, RG58CU, RG142B / U, RG223U, RG400U, Aircell 5, Airborne 5, H 155, H 2005 and Hyperflex 5. It comes standard with one earth connection sleeve for RG58 and another sleeve for the slightly thicker cable types. Type: BNC angle connector Version: 90 degree angle connectorConnection: solder versionCable inlet Ø6,0 mm We use these connectors for the prefabricated H 155 and Hyperflex 5 and RG58 coaxial cables. Assembly instructions
Solder ''BNC'' female connector 5-6mm Our 50 Ohm soldering BNC socket with sealing ring, PTFE dielectric, gold-plated center pin. Available for cables with 5-6mm (H155, Hyperflex 5, Aircell 5). Our BNC cable socket is suitable for all cables of the RG 58 dimension as well as for all cables of the H 155 / Hyperflex 5 series. This BNC socket is provided with 2 ground connection sleeves and 2 center pins. The sleeve with the larger receptacle is designed for H 155 and similar cables. The same applies to the center contact with the larger solder hole. The center contacts are diamagnetic.
Der Problemlöser für 5mm Kabel mit N-Norm Schwierige Position der Buchse am Gerät, die man nur mit einem Adapter lösen kann, dieser dann aber zu lang wird? Warum nicht gleich einen Winkelstecker auf das Kabel montieren? Dieser hochwertige N-Winkelstecker ist für die 5mm Koaxkabeltypen wie RG58U, RG58CU, RG142B/U, RG223U, RG400U, Aircell 5, Airborne 5, H 155, H 2005 und Hyperflex 5 geeignet. Er wird standardmäßig mit einer Masseverbindungshülse ausgeliefert. Herstellernummer: UG 594-6 TA
N-Stecker Crimp Dieser N-Stecker ist zum Krimpen auf H155, Hyperflex 5, Aircell 5 & Airborne 5 Koaxialkabel geeignet. Mit PTFE-Dielektrikum und vergoldetem Mittelkontakt.
N-Connector special 5-6 mm This high-quality N connector is suitable for the coax cable types: RG58U, RG58CU, RG142B/U, RG223U, RG400U, Aircell 5, Airborne 5, H 155, H 2005 und Hyperflex 5. It is equipped as standard with two ground connection sleeves for RG58 and the thicker H 155, Hyperflex 5 etc. Type: N connector special Design: Connector Connection: Soldering Cable inlet Ø6 mm
Original Messi & Paoloni N-Stecker - EVO 5,0mm Messi & Paoloni PL-Stecker CO.N.5M-S EVO – Hochwertiger, verlustarmer N-Stecker für 5 mm-Koaxialkabel.Der CO.N.5M-S EVO ist die neueste Generation der beliebten N-Stecker von Messi & Paoloni, entwickelt für maximale Leitfähigkeit und mechanische Stabilität. Durch seine präzise CNC-Fertigung, vernickelte Messingteile und eine zuverlässige Zugentlastung garantiert dieser Stecker optimale HF-Performance bei gleichzeitig einfacher Montage.Perfekt abgestimmt auf Koaxkabel wie RG-58, Airborne 5, RG 142BU, HF-195, Aircell 5 oder vergleichbare 5 mm-Kabel. Dank der EVO-Serie bietet der Stecker einen verbesserten Kontaktübergang, minimierte Übergangsdämpfung und hervorragende Korrosionsbeständigkeit – ideal für Amateurfunk, CB-Funk, Kurzwellen-Empfangsanlagen oder Antenneninstallationen im Freien.Technische Merkmale:Typ: N-Stecker (N-Male)Modell: CO.N.5M-S EVOPassend für 5 mm-Koaxkabel (z. B. RG-58, Airborne 5, RG 142BU, HF-195, Aircell 5)Material: Vernickeltes Messing, PTFE-IsolatorLötbare Ausführung – robust und HF-dichtEVO-Design mit verbesserter Leitfähigkeit und ZugentlastungMarke: Messi & Paoloni (Made in Italy) Weitere MerkmaleKompressionsdesign mit doppelter Dichtung, die einen besseren Schutz gegen das Eindringen von Wasser, Feuchtigkeit und Kondenswasser gewährleistet.Einfache Installation und Lötanleitung im Paket enthalten (kein Lötgeflecht erforderlich). Drastische Unterdrückung des Hintergrundrauschens, Verbesserung der Schirmdämpfung und der Einfügungsverluste. Die Oberflächen sind mit einer speziellen Legierung namens Smart3-Alloy® behandelt: Sie ist korrosionsbeständig und antiallergisch. Der neu konzipierte Stift verhindert einen Zinnüberschuss und die daraus resultierende Erwärmung, die das Dielektrikum beschädigt und zu einer unkontrollierbaren Veränderung der elektrischen Eigenschaften Ihres Kabels führt. Fazit:Der CO.N.5M-S EVO ist die perfekte Wahl für Funkamateure und Techniker, die höchste Signalqualität und langlebige Verbindungen verlangen. Ein professioneller N-Stecker, der Leistung und Zuverlässigkeit vereint – Made by Messi & Paoloni. Messi & Paoloni Code: CO.N.5M-SInformationen gemäß Art. 19 GPSRHersteller: Messi&PaoloniHerstellername: Messi & Paoloni SrlHandelsname: Messi & PaoloniAdresse: Via Giovanni Conti 1 - 60131 ANCONA, ItalyE-Mail: web@messi.itWebseite: https://messi.it/Verantwortliche Person:Name: Messi & Paoloni SrlAdresse: Via Giovanni Conti 1 - 60131 ANCONA, ItalyE-Mail: web@messi.itWebseite: https://messi.it/
previously €8.11
Original Messi & Paoloni N-Stecker - EVO 5,4mmDieser hochwertige N-Stecker von Messi & Paoloni ist für die Koaxkabeltypen: Hyperflex 5, Hyperflex 5 Crystal, HF-214, H155, u.ä. mit einem Durchmesser von 5,4mm geeignet. Der Löt-N-Stecker kommt mit Dichtungsring, PTFE-Dielektrikum und vergoldetem Mittelstift zu Ihnen. Die zwei mitgelieferten PTFE-Scheiben ermöglichen eine einfache Installation des Steckers. Die PTFE-Scheiben und eine ringförmige Verdickung auf dem Mittelkontakt verhindern, dass das Kabel bei mechanischer Belastung aus der festgelegten Position gezogen werden kann.Kompressionsdesign mit doppelter Dichtung, die einen besseren Schutz gegen das Eindringen von Wasser, Feuchtigkeit und Kondenswasser gewährleistet.Einfache Installation und Lötanleitung im Paket enthalten (kein Lötgeflecht erforderlich). Drastische Unterdrückung des Hintergrundrauschens, Verbesserung der Schirmdämpfung und der Einfügungsverluste. Die Oberflächen sind mit einer speziellen Legierung namens Smart3-Alloy® behandelt: Sie ist korrosionsbeständig und antiallergisch. Der neu konzipierte Stift verhindert einen Zinnüberschuss und die daraus resultierende Erwärmung, die das Dielektrikum beschädigt und zu einer unkontrollierbaren Veränderung der elektrischen Eigenschaften Ihres Kabels führt. Messi & Paoloni Code: CO.N.54M-S Informationen gemäß Art. 19 GPSRHersteller: Messi&PaoloniHerstellername: Messi & Paoloni SrlHandelsname: Messi & PaoloniAdresse: Via Giovanni Conti 1 - 60131 ANCONA, ItalyE-Mail: web@messi.itWebseite: https://messi.it/Verantwortliche Person:Name: Messi & Paoloni SrlAdresse: Via Giovanni Conti 1 - 60131 ANCONA, ItalyE-Mail: web@messi.itWebseite: https://messi.it/
previously €8.11
N socket connector 5-6mm Our 50 Ohm solder N socket with sealing ring, PTFE dielectric, gold-plated center pin. Available for cables with 5-6mm (H155, Hyperflex 5, Aircell 5). Our N cable socket is suitable for all cables of RG 58 dimensions (RG58, Aircell 5, Airborn 5 etc.) as well as for all cable types with 5.4mm of the H 155, Hyperflex 5. This N socket is provided with 2 ground connection sleeves and 2 center pins. The sleeve with the larger receptacle is designed for H 155 and similar cables. The same applies to the center contact with the larger solder hole. The center contacts are diamagnetic. Usable for:RG 58 CU, H 155, Hyperflex 5, Aircell 5, Airborne 5, H 2005, RG 223 U, RG 400 U, RG 142 BU and similar
SMA connector crimpThese SMA connectors are suitable for crimping onto H155, Hyperflex 5, Aircell 5 and Airborne 5 coaxial cables. It has a PTFE dielectric and a gold plated center contact and case.
Dieser hochwertige TNC-Stecker zum Löten hat ein vernickeltes Steckergehäuse, PTFE-Dielektrikum und vergoldete Mittelkontakte. Ein Silikon-O-Ring verhindert das Eindringen von Wasser über das Gewinde. Geeignet für: H 155, H 155 FRNC, H 155 PE, Hyperflex 5 und ähnliche
UHF PL 259 connector for 5 to 6 mm coaxial cables such as RG58, Airborn 5, Aircel 5, H155, Hyperflex 5, HF214, with PTFE insulation and gold-plated center contact. Assembly: The connector is assembled according to the well-known "twist-on principle" by unscrewing and soldering the center contact.