Common-Mode Choke / RFI-Choke Standard (1 KW) – N-Version
€49.00
Available, delivery time: 2-5 days
Product information "Common-Mode Choke / RFI-Choke Standard (1 KW) – N-Version"
Common-Mode Choke / RFI-Choke Standard (1 KW) – N-Version
This common-mode choke prevents the shield of the coaxial cable from becoming part of the antenna system and radiating unintentionally. It also helps match unbalanced coaxial feed lines to balanced antennas and can therefore be used as a 1:1 balun.
Built according to the proven W2DU principle, this standard common-mode choke offers broadband performance with very low loss. A series of high-permeability ferrite cores are threaded onto high-temperature-resistant PTFE coaxial cable, shrink-wrapped, and fitted with high-quality N connectors, allowing easy integration into the coaxial feed line.
The choke is approximately 48 cm long and provides around 1000 ohms of common-mode impedance across a wide frequency range from 80 m to 2 m. It is weatherproof, shrink-wrapped, and equipped with N-type connectors featuring PTFE dielectric and gold-plated contacts on both ends.
Important Installation Note:
When using an end-fed antenna, do not install the common-mode choke directly at the feed point. A section of coaxial cable with a minimum length of λ 0.05 (for example approx. 4.2 m on the 80 m band) should be installed between the end-fed transformer and the choke.
Features
- Frequency range: 3 MHz to 200 MHz
- Attenuation: approx. 25 dB – common-mode impedance approx. 1000 Ω
- Connectors: N-type male to N-type female
- Power handling: approx. 1000 W
- Weight: 0.3 kg
- Length: 48 cm
Informationen gemäß Art. 19 GPSR
Adresse des Herstellers: Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net
Adresse der verantwortlichen Person: Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net
Accessory Items
End Fed Multiband Antenna for 10-15-20-40-80m 300Watts PEP Phone You don't have time to build an Endfed Multiband Antenna? No problem. We offer you a ready assembled End Fed Multiband for the bands 10-15-20-40-80 meters up to 300 Watt PEP Phone. The antenna is tuned to band center. You only have to tune the antenna (as usual) minimally to the desired band section. This End Fed Multiband Antenna includes the following parts in addition to the standard components:Mounting plate, ring, thimble, ground connection, deluxe extension coil and a pressure equalization valve. This End Fed Multiband Antenna comes with: Copper/Kevlar antenna litz wire This antenna litz wire is manufactured specifically for antennas. The litz consists of a Kevlar core with approx. 1.1 mm2 tinned and fine stranded copper conductors. 1x 0.4 mm Kevlar and 24x 0.25 mm copper. The jacket is made of black UV-resistant PE. The total diameter is approx. 2.5 mm. The tensile strength is approx. 50 kg. You will receive a strong, flexible and relatively light antenna litz wire. Type: Multiband Length: approx. 23 meters Connection: PL Max. Power: 300Watt PEP Phone Weight: ca 650g Info The measurements for this antenna were made on two 12m spider beam masts, 10 meters above the ground, in an open field, without any buildings. Informationen gemäß Art. 19 GPSR Adresse des Herstellers: Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net Adresse der verantwortlichen Person: Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net
You don't have time to build an Endfed Multiband Antenna? No problem. We offer you a ready assembled End Fed Multiband for the bands 10-12-15-17-20-(30*)-40-80-160 meters up to 1000 Watts PEP Phone. The antenna is tuned to band center. You only have to tune the antenna (as usual) minimally to the desired band section. This End Fed Multiband Antenna includes the following parts in addition to the standard components:Mounting plate, ring, thimble, ground connection, deluxe extension coil and a pressure equalization valve. This End Fed Multiband Antenna comes with: Copper/Kevlar antenna litz wire This antenna litz wire is manufactured specifically for antennas. The litz consists of a Kevlar core with approx. 1.1 mm2 tinned and fine stranded copper conductors. 1x 0.4 mm Kevlar and 24x 0.25 mm copper. The jacket is made of black UV-resistant PE. The total diameter is approx. 2.5 mm. The tensile strength is approx. 50 kg. You will receive a strong, flexible and relatively light antenna litz wire. Type: Multiband 1:64 Length: approx. 46 meters Connection: PL Max. Power: 1000Watts PEP Phone Weight: ca 750g Info The measurements for this antenna were made on two 12m spider beam masts, 10 meters above the ground, in an open field, without any buildings. Informationen gemäß Art. 19 GPSR Adresse des Herstellers: Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net Adresse der verantwortlichen Person: Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net
End Fed multiband antenna DIY kit for 10-15-20-40-80m 300Watt PEP SSBNew extended kit! This kit contains all the necessary components to build an EndFed 1:49 multiband antenna for the bands 10-15-20-40-80 meters up to 300 Watt PEP Phone. We have added a connection for the counterweight and the useful stainless steel ring etc. to the kit. This End Fed kit is supplied with the antenna wire of your choice: Standard antenna wire: This antenna wire consists of 1.0 mm2 fine stranded copper conductor with black PVC insulation. The total diameter is approx. 2 mm. Ideal for experiments or vacation antennas. As the core is only made of copper, this stranded wire will become slightly longer and therefore thinner over time. The tensile strength of this stranded antenna wire is limited. LF Antenna Strand - New!This high-quality antenna strand consists of 32 individual 0.20 mm wires made of hard-drawn, bare copper. The conductor cross-section is approximately 1.0 mm² and offers excellent conductivity combined with high mechanical strength. It has a total diameter of 2.1 mm, a weight of approx. 11 g/m, and a breaking load of about 40 kg. The robust black polyethylene (PE) insulation reliably protects the strand from environmental influences and ensures a long service life. The kit contains the following components: 1x toroidal core FT-240-431x enameled copper wire GR2 for winding the toroidal core (1mm) approx. 1.50 meters1x polycarbonate housing with transparent cover 100x100x60 mm (IP67)1x mini insulator 65 * 15mm2x simplex terminals up to 2 mm wire (wire rope terminal) 1x thimble approx. 23.5 meter antenna wire 1mm² black 1x capacitor 100pF 2kV DC 1x PL259 panel jack 1x extension coil 110uH ready wound and measured 1x shrink tube black 25.4-12.7mm 1x various screws, washers and nuts made of stainless steel 1x stainless steel ring 3x Fast-On ring contactType: MultibandLength: approx. 23 meters Connection: PL Max. Power: 300Watt PEP Phone Weight: approx. 600g Balun 1:49Informationen gemäß Art. 19 GPSR Adresse des Herstellers: Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.netAdresse der verantwortlichen Person: Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net
End Fed Multiband Antenna for 10*-15-20-40-80m 1000Watts PEP Phone You don't have time to build an Endfed Multiband Antenna? No problem. We offer you a ready assembled End Fed Multiband for the bands 10*-15-20-40-80 meters up to 1000 Watt PEP Phone. The antenna is tuned to band center. You only have to tune the antenna (as usual) minimally to the desired band section. This End Fed Multiband Antenna includes the following parts in addition to the standard components:3 instead 1 one ferrite core, Mounting plate, ring, thimble, ground connection, deluxe extension coil and a pressure equalization valve. This End Fed Multiband Antenna comes with: Copper/Kevlar antenna litz wire This antenna litz wire is manufactured specifically for antennas. The litz consists of a Kevlar core with approx. 1.1 mm2 tinned and fine stranded copper conductors. 1x 0.4 mm Kevlar and 24x 0.25 mm copper. The jacket is made of black UV-resistant PE. The total diameter is approx. 2.5 mm. The tensile strength is approx. 50 kg. You will receive a strong, flexible and relatively light antenna litz wire. Type: Multiband Length: approx. 23 meters Connection: PL Max. Power: 1000Watt PEP Phone Max Powaer digitaL: <100 Watts Weight: ca 1100g 10m needs a tuner Info The measurements for this antenna were made on two 12m spider beam masts, 10 meters above the ground, in an open field, without any buildings.
Similar Items
Common-Mode Choke / RFI-Choke Standard 1 KW This common-mode choke prevents the shield of the coaxial cable from becoming part of the antenna system and radiating unintentionally. It also serves to match the unbalanced coaxial cable to balanced antennas and can therefore be used as a “1:1” balun.Built according to the W2DU principle, the 1 KW common-mode choke is extremely broadband and low-loss. A large number of high-permeability ferrites are threaded onto high-temperature-resistant PTFE coaxial cable, shrink-wrapped, and fitted with appropriate connectors. This makes it easy to integrate into the coaxial feed line.This Standard common-mode choke is approximately 45 cm long, very broadband, and provides about 1000 ohm of common-mode impedance in the frequency range from 80m to 2 m. It is weatherproof shrink-wrapped and has two high-quality PL259 connectors with PTFE dielectric and gold-plated contacts at the ends. A PL259 connector with PTFE and gold-plated contacts is included. Important Notice:When using an End Fed antenna, do not place the common-mode choke directly at the feed point of the antenna! A section of coaxial cable with a length of ≥ λ 0.05 (e.g., about 4.2 m on 80 m band) should be inserted between the End Fed transformer and the common-mode choke.Informationen gemäß Art. 19 GPSR Adresse des Herstellers: Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net Adresse der verantwortlichen Person: Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net
This common-mode choke prevents the shield of the coaxial cable from becoming part of the antenna system and radiating unintentionally. It also serves to match the unbalanced coaxial cable to balanced antennas and can therefore be used as a “1:1” balun. Built according to the W2DU principle, the Wideband 2 KW choke is extremely broadband and low-loss. A large number of high-permeability ferrite sleeves (28 pieces) are threaded onto high-temperature-resistant PTFE coaxial cable, shrink-wrapped, and fitted with suitable connectors. This makes it easy to integrate into the coaxial feed line. The Wideband 2 KW common-mode choke is approximately 70 cm long, very broadband and provides about 1500 ohm of common-mode impedance in the frequency range from 160 m to 2 m (1 MHz to 200 MHz). It is weatherproof with shrink wrap and has two high-quality PL259 connectors with PTFE dielectric and gold-plated contacts at the ends. A PL259 connector with PTFE and gold-plated contacts is included. Important Notice: When using an End Fed antenna, do not place the common-mode choke directly at the feed point of the antenna! A section of coaxial cable with a length of ≥ λ 0.05 (e.g., about 4.2 m on the 80 m band) should be inserted between the End Fed transformer and the common-mode choke. Informationen gemäß Art. 19 GPSR Adresse des Herstellers: Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net Adresse der verantwortlichen Person: Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net
Common-Mode Choke / RFI-Choke Wideband (2 KW) – N-Version This wideband common-mode choke prevents the shield of the coaxial cable from becoming part of the antenna system and radiating unintentionally. It also helps match an unbalanced coaxial feed to balanced antennas and can therefore be used as a 1:1 balun.Built according to the W2DU principle, the wideband 2 KW choke delivers extremely broadband, low-loss performance. A large number of high-permeability ferrite sleeves are threaded onto high-temperature-resistant PTFE coaxial cable, shrink-wrapped, and fitted with high-quality N-type connectors, making it easy to integrate into your coaxial feed line.The choke is approximately 72 cm long and provides around 1500 ohms of common-mode impedance over a wide frequency range from 160 m to 2 m (1 MHz – 200 MHz). It is weatherproof, shrink-wrapped, and equipped with premium N-type connectors (plug and socket) with PTFE dielectric and gold-plated contacts.Important Installation Note:When using an end-fed antenna, do not install the choke directly at the antenna feed point. A section of coaxial cable with a minimum length of ≥ λ 0.05 (for example about 4.2 m on the 80 m band) should be placed between the end-fed transformer and the choke. FeaturesFrequency range: 1 MHz to 200 MHzAttenuation: approx. 32 dB – common-mode impedance approx. 1500 ΩConnectors: High-quality N-type male to N-type femalePower handling: approx. 2000 WWeight: 0.5 kgLength: 72 cmInformationen gemäß Art. 19 GPSR Adresse des Herstellers: Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net Adresse der verantwortlichen Person: Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net
1 – 30 MHz Common mode filter with bifilaire windings for optimal attenuation There are many types of common mode chokes available, HF Kits opts for a common mode choke with bifilar windings for optimal filtering. This 1 – 30 MHz common mode current filter is optimized for the 80 and 160 meter band. In this case a FT240-31 toroidal core with optimal performance for the lower frequency range is used. The 1 – 30 MHz common mode choke performs very well on the entire HF spectrum. The attenuation is therefore around 30 dB across the entire HF frequency spectrum. This filter is therefore a real all-rounder for amateurs who want to work from 160 meters to 10 meters. Even people who deal with LPAM (Medium Wave) can use this filter. The main reason for using a common mode choke is to ensure that the coax cable’s shield does not become part of the antenna system and will radiate unintentionally. This has all sorts of nasty effects, think of: interference issues, disrupted radiation pattern of the antenna and a higher noise level. This last point is because not only does the coax cable’s shield radiate when you transmit, but the shield also works as a receiving antenna. Because the coax cable often makes a considerable trip within the house, close to interference sources (mains, PLC etc…) It is useful to eliminate these sources of interference. Any way, Good reason to use a common mode choke. The effect of this common mode choke with bifilar windings is difficult to predict. This depends on local circumstances. Think of: antenna type, antenna placement, type of feed line, feed line placement and especially local sources of interference. There are manufacturers that promise in advance a significant drop in interference, however this is not real. There are cases where the noise level decreases by two to three S points, but also cases where the filter has almost no effect. This kit includes: IP65 enclosure 100 x 100 x 55 mm (Polycarbonat) Ringcore Amidon FT240-31 Winding wire 18 AWG – 4x 85cm PTFE 19 x 0.25 mm copper “Silver plated” Toroid mounting plate Stainless steel M3 6mm screws 4x Stainless steel M3 Spring washer 4x 2x PL 259 Chassis 2x M3 cable lug 8x Stainless steel M3 Bolt 12mm 8x Stainless Steel M3 Nut 8x Stainless steel M3 washer 8x Stainless steel M3 tooth washer IMPORTANT! Do not place the common mode choke in case of an End Fed antenna directly at feed point of the antenna.Construction Manual in Englisch