End Fed Antennas
Mosquito End Fed 1:9 Antenna Mosquito End Fed – small and light After the Mini-End Fed was so well accepted, we looked at how we could make the whole thing even smaller, more compact but robust. The main focus here was on weight. The result is the Moskito End Fed. Mosquito? Yes, because it is so tiny and light. The cylindrical housing with a height of only 70mm and a diameter of 25mm weighs just 50 grams. This makes the Moskito easy to stow in your pocket or backpack. The maximum output is 50 watts SSB PEP. It is available in 1:49 and 1:9. This makes the Moskito End Fed antenna ideal for portable use when traveling, QRP, COTA, POTA, IOTA, SOTA (Summit on the Air) or DX expeditions etc. The Moskito End Fed is suitable for the new generation of small multiband/multimode QRP transceivers such as the Icom IC-705, Xiegu G90 or X6100, LAB 599 TX500 or the Yaesu FT-817/818. Super light antenna wire To match the lightweight Moskito End Fed, we offer the new, super lightweight and high-strength antenna wire SL as an option. This antenna wire is only 1.6mm thick, weighs 4g per meter and consists of 6×0.25mm tinned copper wires. The stranded wire has a core made of tear-resistant Vectran fibers® and a weatherproof PE insulation. This achieves a maximum breaking load of up to 60kg! If you attach the antenna to the top of a telescopic mast and slide out the mast segments, you can be on air within a few minutes! To attach the housing of the 1:9 transformer to a mast, the mini insulator and a carabiner are all you need. Counter-poise If a counter-poise is required, you can connect a short piece of wire/strand with a length of 0.05 λ to the side connection of the mosquito antenna. The counter-poise should hang down freely.
Mosquito End Fed 1:49 – small and light After the Mini-End Fed was so well accepted, we looked at how we could make the whole thing even smaller, more compact but robust. The main focus here was on weight. The result is the Moskito End Fed. Mosquito? Yes, because it is so tiny and light. The cylindrical housing with a height of only 70mm and a diameter of 25mm weighs just 50 grams. This makes the Moskito easy to stow in your pocket or backpack. The maximum output is 50 watts SSB PEP. It is available in 1:49 and 1:9. This makes the Moskito End Fed antenna ideal for portable use when traveling, QRP, COTA, POTA, IOTA, SOTA (Summit on the Air) or DX expeditions etc. The Moskito End Fed is suitable for the new generation of small multiband/multimode QRP transceivers such as the Icom IC-705, Xiegu G90 or X6100, LAB 599 TX500 or the Yaesu FT-817/818. Super light antenna wire To match the lightweight Moskito End Fed, we offer the new, super lightweight and high-strength antenna wire SL as an option. This antenna wire is only 1.6mm thick, weighs 4g per meter and consists of 6×0.25mm tinned copper wires. The stranded wire has a core made of tear-resistant Vectran fibers® and a weatherproof PE insulation. This achieves a maximum breaking load of up to 60kg! If you attach the antenna to the top of a telescopic mast and slide out the mast segments, you can be on air within a few minutes! To attach the housing of the 1:9 transformer to a mast, the mini insulator and a carabiner are all you need. Counter-poise If a counter-poise is required, you can connect a short piece of wire/strand with a length of 0.05 λ to the side connection of the mosquito antenna. The counter-poise should hang down freely.
Mini End Fed Multiband Antenna You don't have time to build a Mini End Fed Multiband Antenna?No problem. We offer you a ready made Mini End Fed Multiband Antenna for the bands 10-15-20-40m or 10-15-20-40-80m up to 100 Watt PEP Phone. The antenna is tuned to band center. You only have to tune the antenna (as usual) minimally to the desired band area. The Mini Endfed is a small end fed antenna solution for mobile use, travel, QRP, SOTA (Summit on the Air) or DX expeditions etc. The IP65 protected polycarbonate case with a size of only 64x58x35 mm, can be easily stored in your pocket or backpack. The weight is about 400-500 grams, depending on the radiator length. This Mini End Fed antenna includes the following parts in addition to the standard parts: thimble, ground connection, deluxe extension coil. This End Fed Multiband Antenna comes with the antenna wire of your choice: Standard Antenna wire: This antenna litz wire is made of 1.0 mm2 fine stranded copper conductor with a black PVC insulation. The total diameter is about 2 mm. Ideal for experiments or vacation antennas. Since the core is only copper, this stranded wire will always elongate a bit over time, making it thinner. The tensile strength of this antenna strand is limited. Copper/Kevlar antenna litz wire This antenna litz wire is manufactured specifically for antennas. The litz consists of a Kevlar core with approx. 1.1 mm2 tinned and fine stranded copper conductors. 1x 0.4 mm Kevlar and 24x 0.25 mm copper. The jacket is made of black UV-resistant PE. The total diameter is approx. 2.5 mm. The tensile strength is approx. 50 kg. You will receive a strong, flexible and relatively light antenna litz wire. Technical dataType: MultibandLength: approx. 12 (10-40m) or 23 meters (10-80m)Connection: BNCMax. Power: 100Watt PEP PhoneWeight: approx. 250g Informationen gemäß Art. 19 GPSR Adresse des Herstellers: Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net Adresse der verantwortlichen Person: Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net
1:9 UNUN transformer for the frequency range: 1-30MHz and a maximum transmission power of either 600W or 1500W PEP. The IP67 housing is of course made of UV-resistant polycarbonate. Including connection for a counterweight and, for market launch, with mast mounting shown. All screws and nuts are made of stainless steel. The PL or N sockets used are high quality and PTFE dialectic. A tuner is required for non-resonant antennas. The following wire lengths have proven to be useful:6.5m - 6.9m - 13.5m - 13.9m - 16.2m - 20.8m - 22m - 26m - 27.7m - 34.7m - 41.6m - 48.5m - 55.5m You can find suitable antenna strands here: Copper Kevlar stranded wireInformationen gemäß Art. 19 GPSR Adresse des Herstellers: Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net Adresse der verantwortlichen Person: Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net
End Fed Multiband Antenna for 10-15-20-40-80m 300Watts PEP Phone You don't have time to build an Endfed Multiband Antenna? No problem. We offer you a ready assembled End Fed Multiband for the bands 10-15-20-40-80 meters up to 300 Watt PEP Phone. The antenna is tuned to band center. You only have to tune the antenna (as usual) minimally to the desired band section. This End Fed Multiband Antenna includes the following parts in addition to the standard components:Mounting plate, ring, thimble, ground connection, deluxe extension coil and a pressure equalization valve. This End Fed Multiband Antenna comes with: Copper/Kevlar antenna litz wire This antenna litz wire is manufactured specifically for antennas. The litz consists of a Kevlar core with approx. 1.1 mm2 tinned and fine stranded copper conductors. 1x 0.4 mm Kevlar and 24x 0.25 mm copper. The jacket is made of black UV-resistant PE. The total diameter is approx. 2.5 mm. The tensile strength is approx. 50 kg. You will receive a strong, flexible and relatively light antenna litz wire. Type: Multiband Length: approx. 23 meters Connection: PL Max. Power: 300Watt PEP Phone Weight: ca 650g Info The measurements for this antenna were made on two 12m spider beam masts, 10 meters above the ground, in an open field, without any buildings.
End Fed Multiband Antenna for 10-15-20-40-80m 300Watts PEP Phone You don't have time to build an Endfed Multiband Antenna? No problem. We offer you a ready assembled End Fed Multiband for the bands 10-15-20-40-80 meters up to 300 Watt PEP Phone. The antenna is tuned to band center. You only have to tune the antenna (as usual) minimally to the desired band section. This End Fed Multiband Antenna includes the following parts in addition to the standard components:Mounting plate, ring, thimble, ground connection, deluxe extension coil and a pressure equalization valve. This End Fed Multiband Antenna comes with: Copper/Kevlar antenna litz wire This antenna litz wire is manufactured specifically for antennas. The litz consists of a Kevlar core with approx. 1.1 mm2 tinned and fine stranded copper conductors. 1x 0.4 mm Kevlar and 24x 0.25 mm copper. The jacket is made of black UV-resistant PE. The total diameter is approx. 2.5 mm. The tensile strength is approx. 50 kg. You will receive a strong, flexible and relatively light antenna litz wire. Type: Multiband Length: approx. 23 meters Connection: PL Max. Power: 300Watt PEP Phone Weight: ca 650g Info The measurements for this antenna were made on two 12m spider beam masts, 10 meters above the ground, in an open field, without any buildings. Informationen gemäß Art. 19 GPSR Adresse des Herstellers: Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net Adresse der verantwortlichen Person: Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net
End Fed Multiband Antenna for 10-12-15-17-20-(30*)-40-80-1600m - 300Watts PEP Phone You don't have time to build an Endfed Multiband Antenna? No problem. We offer you a ready assembled End Fed Multiband for the bands 10-12-15-17-20-(30*)-40-80-160 meters up to 300/600Watts PEP Phone. The antenna is tuned to band center. You only have to tune the antenna (as usual) minimally to the desired band section. This End Fed Multiband Antenna includes the following parts in addition to the standard components:Mounting plate, ring, thimble, ground connection, deluxe extension coil and a pressure equalization valve. This End Fed Multiband Antenna comes with: Copper/Kevlar antenna litz wire This antenna litz wire is manufactured specifically for antennas. The litz consists of a Kevlar core with approx. 1.1 mm2 tinned and fine stranded copper conductors. 1x 0.4 mm Kevlar and 24x 0.25 mm copper. The jacket is made of black UV-resistant PE. The total diameter is approx. 2.5 mm. The tensile strength is approx. 50 kg. You will receive a strong, flexible and relatively light antenna litz wire. Type: Multiband 1:64 Length: approx. 46 meters Connection: PL Max. Power: 300/600 Watts PEP Phone Weight: ca 750g Info The measurements for this antenna were made on two 12m spider beam masts, 10 meters above the ground, in an open field, without any buildings. Informationen gemäß Art. 19 GPSR Adresse des Herstellers: Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net Adresse der verantwortlichen Person: Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net
End Fed Multiband Antenna for 10*-15-20-40-80m 1000Watts PEP Phone You don't have time to build an Endfed Multiband Antenna? No problem. We offer you a ready assembled End Fed Multiband for the bands 10*-15-20-40-80 meters up to 1000 Watt PEP Phone. The antenna is tuned to band center. You only have to tune the antenna (as usual) minimally to the desired band section. This End Fed Multiband Antenna includes the following parts in addition to the standard components:3 instead 1 one ferrite core, Mounting plate, ring, thimble, ground connection, deluxe extension coil and a pressure equalization valve. This End Fed Multiband Antenna comes with: Copper/Kevlar antenna litz wire This antenna litz wire is manufactured specifically for antennas. The litz consists of a Kevlar core with approx. 1.1 mm2 tinned and fine stranded copper conductors. 1x 0.4 mm Kevlar and 24x 0.25 mm copper. The jacket is made of black UV-resistant PE. The total diameter is approx. 2.5 mm. The tensile strength is approx. 50 kg. You will receive a strong, flexible and relatively light antenna litz wire. Type: Multiband Length: approx. 23 meters Connection: PL Max. Power: 1000Watt PEP Phone Max Powaer digitaL: <100 Watts Weight: ca 1100g 10m needs a tuner Info The measurements for this antenna were made on two 12m spider beam masts, 10 meters above the ground, in an open field, without any buildings.
End Fed Multiband Antenna for 10*-15-20-40-80m 1000Watts PEP Phone You don't have time to build an Endfed Multiband Antenna? No problem. We offer you a ready assembled End Fed Multiband for the bands 10*-15-20-40-80 meters up to 1000 Watt PEP Phone. The antenna is tuned to band center. You only have to tune the antenna (as usual) minimally to the desired band section. This End Fed Multiband Antenna includes the following parts in addition to the standard components:3 instead 1 one ferrite core, Mounting plate, ring, thimble, ground connection, deluxe extension coil and a pressure equalization valve. This End Fed Multiband Antenna comes with: Copper/Kevlar antenna litz wire This antenna litz wire is manufactured specifically for antennas. The litz consists of a Kevlar core with approx. 1.1 mm2 tinned and fine stranded copper conductors. 1x 0.4 mm Kevlar and 24x 0.25 mm copper. The jacket is made of black UV-resistant PE. The total diameter is approx. 2.5 mm. The tensile strength is approx. 50 kg. You will receive a strong, flexible and relatively light antenna litz wire. Type: Multiband Length: approx. 23 meters Connection: PL Max. Power: 1000Watt PEP Phone Max Powaer digitaL: <100 Watts Weight: ca 1100g 10m needs a tuner Info The measurements for this antenna were made on two 12m spider beam masts, 10 meters above the ground, in an open field, without any buildings.
1:9 UNUN transformer for the frequency range: 1-30MHz and a maximum transmission power of either 600W or 1500W PEP. The IP67 housing is of course made of UV-resistant polycarbonate. Including connection for a counterweight and, for market launch, with mast mounting shown. All screws and nuts are made of stainless steel. The PL or N sockets used are high quality and PTFE dialectic. A tuner is required for non-resonant antennas. The following wire lengths have proven to be useful:6.5m - 6.9m - 13.5m - 13.9m - 16.2m - 20.8m - 22m - 26m - 27.7m - 34.7m - 41.6m - 48.5m - 55.5m You can find suitable antenna strands here: Copper Kevlar stranded wire Translated with DeepL.com (free version)