Mini Endfed Multiband Antenne DIY-Bausatz für 10-15-20-40-80m
€61.00
Available, delivery time: 2-5 days
Product information "Mini Endfed Multiband Antenne DIY-Bausatz für 10-15-20-40-80m"
Mini Endfed Antennenbausatz für 10-15-20-40-80m, max 100 Watt PEP Phone und 1:49 Transformator
Die Mini Endfed ist eine kleine End Fed Antennen Lösung für den Portabeleinsatz, auf Reisen, QRP, SOTA (Summit on the Air) oder DX Expeditionen usw. Das IP65 geschütze Gehäuse aus Polcarbonat mit einer Größe von nur 64x58x35 mm, lässt sich leicht in der Tasche oder im Rucksack verstauen, ist aber auch robust genug für die stationäre Montage. Das Gewicht beträgt etwa 400-500 Gramm, je nach Strahlerlänge.
Der Bausatz hat sowohl einen Anschluss für die ANTenne als auch GND für ein Gegengewicht. Den M4 Ring haben wir ebnso integriert. Damit lässt sich die Mini Endfed ganz einfach mit einem Karabiner befestigen und mit der Kausche als Zugentlasung vewenden. Alle Schrauben, Muttern und der Ring sind aus Edelstahl.
Befestigt man die Antenne an der Spitze eine Teleskopmast schiebt die Mastsegmente heraus, ist man innerhalb von wenigen Minuten auf Sendung! Um das Gehäuse des 1:49 Transformers an einem Mast zu befestigen, kann die gleiche Halterung wie von unseren Aktivantennen verwendet werden.
Dieser Mini Endfed-Bausatz wird mit einem Antennendraht Ihrer Wahl geliefert:
Standard Antennenlitze:
Diese Antennenlitze besteht aus 1,0 mm2 feindrähtiger Kupferleiter mit einer schwarzen PVC Isolierung. Der Gesamtdurchmesser beträgt etwa 2 mm. Ideal für Experimente oder Urlaubsantennen. Da der Kern nur aus Kupfer besteht, wird sich diese Litze mit der Zeit immer etwas längen und somit dünner werden. Die Zugfestigkeit dieser Antennenlitze ist begrenzt.
Kupfer/Kevlar-Antennenlitze
Diese Antennenlitze wird speziell für Antennen hergestellt. Die Litze besteht aus einem Kevlarkern mit ca. 1,1 mm2 verzinntem und feindrähtigen Kupferleitern. 1x 0,4 mm Kevlar und 24x 0,25 mm Kupfer. Die Ummantelung besteht aus schwarzem UV-beständigem PE. Der Gesamtdurchmesser beträgt ca. 2,5 mm. Die Zugfestigkeit ist ca. 50 kg. Sie erhalten eine starken, flexible und relativ leichte Antennenlitze.
Diese kompletten Mini End Fed Multiband Bausätze sind für 100 Watt PEP Phone ausgelegt und in diesen Ausführungen erhältlich:
- 10-20-40 Meter ca. 20 Metern Länge, ohne Verlängerungsspule
- 10-20-40 Meter, ca. 12 Metern Länge, mit 34uH Verlängerungsspule
- 10-15-20-40-80 Meter, ca. 21 Metern Länge mit 110uH Verlängerungsspule
Dieser Bausatz enthält:
23 Meter Antennenlitze
19 mm PVC-Rohr mit ca: 110uh Spule (fertig gewickelt und vermessen)
1x Edelstahl Kabelklemme
1x Endisolator
1x Kabelschuh 5mm
1x Schrumpfschlauch
1:49 Mini Impedanztransformator:
IP65-Gehäuse 64x58x35mm Polycarbonat
Ringkern FT140-43
Kupferlackdraht GR2 Qualität 1,00 mm
100 pF Kondensator 2kV
1x BNC-Flanschbuchse
2x M2,5 Schrauben 8/10mm
2x M2,5 Mutter
2x M2,5 Unterlegscheibe
1x Kabelschuh 3mm
3x M5 Kabelschuh
2x Edelstahl M5 Schraube 20mm
2x Edelstahl M5 Flügelmutter
2x Edelstahl M5 Kragenmutter
2x Edelstahl M5 Zahnscheibe
2x Edelstahl M5 Schraube 20mm
2x Edelstahl M5 Flügelmutter
2x Edelstahl M5 Kragenmutter
2x Edelstahl M5 Zahnscheibe
1x Ring M4
1x Zahnscheibe M4
1x Mutter M4
1x Kabelkausche
Die Bauanleitung finden Sie hier: ZUR BAUANLEITUNG
Accessory Items
BNC flange connector BNC flange connector with PTFE dielectric and gold plated center contact. This connector is also used for our Mini-Endfed kits. Hole diameter 3mm
2-Loch UHF / PL Flanschbuchse SO-239 mit PTFE-Isolierung und vergoldetem Mittelkontakt.
This V4A mounting bracket fits for the Boni-Whip, MegActiv, GigActiv and the MegaLoop.
Enclosure for Endfed Antennas Polycarbonate Now with transparent lid! Single enclosure of our EndFed antenna kits, with transparent lid, as a spare part or just for experimenting. The enclosre is made of polycarbonate, as in the kit. Polycarbonate housings are more weather-resistant and UV-resistant than ABS housings. Dimensions: 100 x 100 x 55mmColour: light greyMaterial: polycarbonateProtection class: IP 65Screws and gasket included
Hamrope PES 4 Our best selling universal guy line for the radio amateur. For portable and stationary use. The quality polyester has excellent UV resistance and is suitable for long-term use. The elasticity of this braided rope has a shock absorbing effect and is desirable and often necessary for the use of radio amateurs. The attractive design allows the product to fit well into a natural environment, yet be perceived sufficiently. Hamrope PES 4 Polyester, 4mm diameter tensile strength approx. 260 daN(~Kg) Colour: olive green with red marker Length: 50 meter
Enclosure for mini Endfed Antennas Polycarbonate Single enclosure of our mini EndFed antenna kits as a spare part or just for experimenting. The enclosre is made of polycarbonate, as in the kit. Polycarbonate housings are more weather-resistant and UV-resistant than ABS housings. Dimensions: 64x58x35mmColour: light greyMaterial: polycarbonateProtection class: IP 65Screws and gasket included
Mini insulator for wire antennas Our mini insulators from our Endfed kits are now also available seperately. The Mini Isolator can be used multifunctionally, for example as strain relief for dipoles and EndFed antennas. Furthermore it is also suitable as a holder for Endfed antennas or balun housings. Features Color: ClearMaterial: Plastic UV resistantDimensions: 65 x 15 x 8 mm
This pre-assembled coaxial cable with integrated RFI choke for End Fed antennas is ready for immediate use. Thanks to its design based on the W2DU principle, the common mode choke is extremely broadband and low-loss. It effectively prevents the shielding of the coaxial cable from becoming part of the antenna system and radiating unintentionally. It therefore provides effective protection against unwanted RF interference. It also serves to adapt the unbalanced coaxial cable to balanced antennas and can therefore also be used as a “1:1” balun. A variety of highly permeable ferrites are threaded onto lightweight HF-195 FX-ZH low-loss coaxial cable, shrink-wrapped and assembled with connectors as required. The integrated RFI choke (common mode choke) is installed at the end of the cable after 2.10m for the 10-40m bands or after 4.20m for the 10-80m bands. We offer lengths of 10, 15 and 20m. Other lengths can be produced on request. The lightweight coaxial cable with integrated RFI choke (common mode choke) is also ideal for portable use when traveling, QRP, COTA, POTA, IOTA, SOTA (Summit on the Air) or DX expeditions. 50 Ohm HF195 FX-ZH coaxial cableReady for immediate usefor 10-40m or 10-80m bandPlug and PlayChoice of cable lengthConnector of your choicePower limit Max: 250W PEP SSB Translated with DeepL.com (free version)
This pre-assembled coaxial cable with integrated RFI choke for QRP is ready for immediate use. Thanks to its design based on the W2DU principle, the common mode choke is extremely broadband and low-loss. It effectively prevents the shielding of the coaxial cable from becoming part of the antenna system and radiating unintentionally. It therefore provides effective protection against unwanted RF interference. It also serves to adapt the unbalanced coaxial cable to balanced antennas and can therefore also be used as a “1:1” balun. A variety of highly permeable ferrites are threaded onto lightweight RG316 low-loss coaxial cable, shrink-wrapped and assembled with connectors as required. The integrated RFI choke (common mode choke) is installed at the end of the cable after 30cm. We offer lengths of 5,20m, 7,70m and 10,20m. Other lengths can be produced on request. The lightweight coaxial cable with integrated RFI choke (common mode choke) is also ideal for portable use when traveling, QRP, COTA, POTA, IOTA, SOTA (Summit on the Air) or DX expeditions. 50 Ohm high Quality RG316 coaxial cableReady for immediate usePlug and PlayBNC Connector with PTFEChoice of cable lengthPower limit Max: 100W PEP SSB Informationen gemäß Art. 19 GPSR Adresse des Herstellers: Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net Adresse der verantwortlichen Person: Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net
2-Loch N Flanschbuchse Mit PTFE-Isolierung (hoch temperaturbeständig) und vergoldetem Mittelkontakt.
Mini telescopic pole with only 71cm transport length, fits in any suitcase. This pole is easy to carry and ready installed within a minute. Although it is light and small enough to fit in any large suitcase, it was developed to be rugged and durable! This ultra-portable Mini pole has a heavy-duty screw-on base cap at the bottom to protect its segments from rocks and mud. Nubs on the bottom of the pole help prevent slippage. Spiderbeam fiberglass poles are extremely strong, with a much greater wall thickness than the typical "fishing rod" types.It uses a special reinforced winding technique – where several layers of fiberglass are wound in alternating direction (criss-cross wound) – providing greatly increased lateral and linear strength. The Spiderbeam Mini-poles have a much larger overlap between segments than most other fiberglass poles, which assures stronger joints between segments, and results in a much stronger pole. Spiderbeam fiberglass poles are perfect for supporting all kinds of wire antennas.The Spiderbeam Mini poles are great for Geocaching, SOTA, IOTA and any other popular application for traveling ham radio operators. The top segment of the Mini pole is hollow, very rigid and got has a usable inner diameter of 4mm allowing a wire to pass through, or for attaching your mini tool for other applications. Unlike most competitors’ poles where the top segment is a very thin, solid whip, the Spiderbeam Mini pole can be used to its full 7m or 10m length. Technical Data 7 Meters / 23ft fully extracted length (height) 7m (23ft)* transport length 0.71m (2715/16)* weight 1026g (2lbs. 4 oz.) bottom diameter (incl. the cap) 50mm (2")* top diameter 6mm (0.24")* wall thickness 0,7mm - 1,4mm* (0.027" - 0.067")* number of segments 11 pole material black fiberglass, UV protected specially reinforced multilayer winding Technical Data 10 Meters / 32ft fully extracted length (height) 10m (32ft 10")* transport length 0.72m (281/3)* weight 2.220kg (4lbs. 14 oz.)* bottom diameter (cap) 66mm (2 3/5")* bottom diameter (segment) 60mm (21/3")* top diameter 6mm (0.24")* wall thickness 0.7mm - 1.4mm* (0.027"" - 1/18")* number of segments 17 pole material black fiberglass, UV protected specially reinforced multilayer winding
Wire reel for antenna wire With this reel with 15cm diameter, the antenna wire of the Endfed or Mini Endfed can be wound up safely without bending the wire. Ideal for mobile use when traveling, SOTA (Summit on the Air) or DX expeditions etc. Simply wind the antenna cable onto the spool and stow it in your backpack or bag. The bright yellow color makes it easy to find the reel in your bag. 15cm diameter 24mm wide For about 22m antenna wire with 1mm2
Rope clamp Clamcleat® CL260 - pack of 10 pieces Self-locking rope clamps made of high-strength, UV and cold-resistant material (tested in arctic conditions). Easily adjustable and retightenable at any time. For ropes of 2-4mm diameter. Ideal for Hamrope PES4. Material: nylon, color olive green or black, supplied in a pack of 10.
3x snaphooks A4Thanks to their rust resistance (material 316), these stainless steel snaphooks can be used permanently outdoors or in the wet. They have a length of 50 millimeters, with the snap hook measuring five millimeters in diameter. The total weight that this snap hook can support is 95dan, about 85 kilograms. This should be enough for tie-off. Technical data snap hook Length: 50 mmWidth: 25 mmInner length: 40 mmThickness: 5 mmInner width: 15 mmOpening: 7 mminner width eyelet: 8 mmmax. weight load 85 kgmin. breaking load 200 kg