Halterung für End Fed Antennen

End Fed multiband antenna DIY kit for 10-15-20-40-80m 300Watt PEP SSBNew extended kit! This kit contains all the necessary components to build an EndFed 1:49 multiband antenna for the bands 10-15-20-40-80 meters up to 300 Watt PEP Phone. We have added a connection for the counterweight and the useful stainless steel ring etc. to the kit. This End Fed kit is supplied with the antenna wire of your choice: Standard antenna wire: This antenna wire consists of 1.0 mm2 fine stranded copper conductor with black PVC insulation. The total diameter is approx. 2 mm. Ideal for experiments or vacation antennas. As the core is only made of copper, this stranded wire will become slightly longer and therefore thinner over time. The tensile strength of this stranded antenna wire is limited. Copper/Kevlar stranded antenna wire This stranded antenna wire is specially manufactured for antennas. The stranded wire consists of a Kevlar core with approx. 1.1 mm2 tinned and fine-stranded copper conductors. 1x 0.4 mm Kevlar and 24x 0.25 mm copper. The sheathing is made of black UV-resistant PE. The total diameter is approx. 2.5 mm. The tensile strength is approx. 50 kg. You receive a strong, flexible and relatively light antenna strand. The kit contains the following components: 1x toroidal core FT-240-431x enameled copper wire GR2 for winding the toroidal core (1mm) approx. 1.50 meters1x polycarbonate housing with transparent cover 100x100x60 mm (IP67)1x mini insulator 65 * 15mm2x simplex terminals up to 2 mm wire (wire rope terminal) 1x thimble approx. 23.5 meter antenna wire 1mm² black 1x capacitor 100pF 2kV DC 1x PL259 panel jack 1x extension coil 110uH ready wound and measured 1x shrink tube black 25.4-12.7mm 1x various screws, washers and nuts made of stainless steel 1x stainless steel ring 3x Fast-On ring contactType: MultibandLength: approx. 23 meters Connection: PL Max. Power: 300Watt PEP Phone Weight: approx. 600g Balun 1:49

End Fed multiband antenna DIY kit for 10-20-40m 300Watt PEP SSBNew extended kit! This kit contains all the necessary components to build an EndFed 1:49 multiband antenna for the bands 10-20-40meters up to 300 Watt PEP Phone. We have added a connection for the counterweight and the useful stainless steel ring etc. to the kit. This End Fed kit is supplied with the antenna wire of your choice: Standard antenna wire: This antenna wire consists of 1.0 mm2 fine stranded copper conductor with black PVC insulation. The total diameter is approx. 2 mm. Ideal for experiments or vacation antennas. As the core is only made of copper, this stranded wire will become slightly longer and therefore thinner over time. The tensile strength of this stranded antenna wire is limited. Copper/Kevlar stranded antenna wire This stranded antenna wire is specially manufactured for antennas. The stranded wire consists of a Kevlar core with approx. 1.1 mm2 tinned and fine-stranded copper conductors. 1x 0.4 mm Kevlar and 24x 0.25 mm copper. The sheathing is made of black UV-resistant PE. The total diameter is approx. 2.5 mm. The tensile strength is approx. 50 kg. You receive a strong, flexible and relatively light antenna strand. The kit contains the following components: 1x toroidal core FT-240-431x enameled copper wire GR2 for winding the toroidal core (1mm) approx. 1.50 meters1x polycarbonate housing with transparent cover 100x100x60 mm (IP67)1x mini insulator 65 * 15mm2x simplex terminals up to 2 mm wire (wire rope terminal) 1x thimble approx. 23.5 meter antenna wire 1mm² black 1x capacitor 100pF 2kV DC 1x PL259 panel jack 1x extension coil 34uH ready wound and measured 1x shrink tube black 25.4-12.7mm 1x various screws, washers and nuts made of stainless steel 1x stainless steel ring 3x Fast-On ring contactType: MultibandLength: approx. 12 meters Connection: PL Max. Power: 300Watt PEP Phone Weight: approx. 600g Balun 1:49

End Fed Multiband Antenne DIY-Bausatz 1:64 für 10-12-15-17-20-(30*)-40-80-160m - 300Watt PEP SSB In diesem Bausatz sind alle nötigen Bauteile zum Bau einer 1:64 End Fed Multiband Antenne für die Bänder: 10-12-15-17-20-(30*)-40-80-160 Meter bis 300 Watt PEP Phone enthalten. Wir haben den Bausatz um einen Anschluss für das Gegengewicht und um den nützlichen Edelstahlring etc. erweitert. Dieser End Fed-Bausatz wird mit der Antennenlitze Ihrer Wahl geliefert: Standard Antennenlitze:Diese Antennenlitze besteht aus 1,0mm2 feindrähtiger Kupferleiter mit einer schwarzen PVC Isolierung. Der Gesamtdurchmesser beträgt etwa 2 mm. Ideal für Experimente oder Urlaubsantennen. Da der Kern nur aus Kupfer besteht, wird sich diese Litze mit der Zeit immer etwas längen und somit dünner werden. Die Zugfestigkeit dieser Antennenlitze ist begrenzt. Kupfer/Kevlar-AntennenlitzeDiese Antennenlitze wird speziell für Antennen hergestellt. Die Litze besteht aus einem Kevlarkern mit ca. 1,1 mm2 verzinntem und feindrähtigen Kupferleitern. 1x 0,4 mm Kevlar und 24x 0,25 mm Kupfer. Die Ummantelung besteht aus schwarzem UV-beständigem PE. Der Gesamtdurchmesser beträgt ca. 2,5 mm. Die Zugfestigkeit ist ca. 50 kg. Sie erhalten eine starke, flexible und relativ leichte Antennenlitze. Der Bausatz enthält die folgenden Bauteile:  1x Ringkern: FT-2401x Kupferlackdraht GR2 für die Wicklung des Ringkerns (1mm) ca. 1,50 Meter1x Polycarbonat Gehäuse mit Klarsichtdeckel 100x100x60 mm (IP67)1x Mini-Isolator 65 * 15mm transparent2x Simplex Klemmen bis 2 mm Draht (Drahtseilklemme)1x Kauscheca. 47 Meter Antennenkabel 1mm² schwarz1 x Kondensator 100 pF 3kVDC1 x PL259 Einbaubuchse1x Verlängerungsspule 192uH fertig gewickelt und gemessen1 x Schrumpfschlauch schwarz 25.4-12.7mm1x Verschiedene Schrauben und Muttern aus Edelstahl3x Fast-On Ringkontakt1x Edelstahlring Länge: ca. 47 Meter Anschluss: PL/SO239 Max. Leistung: 300Watt PEP Phone Gewicht: ca 500g Balun 1:64 TIPP Ich kann nur jedem empfehlen, die Montageplatte für den Ringkern gleich mitzubestellen. Damit ist der Ringkern befestigt und hängt nicht an den Drähten, lose im Gehäuse herum. Gerade bei Wind ein großer Voteil. Neue Bauanleitung 7/2023 https://www.bonito.net/hamradio/bauanleitung-end-fed-bausatz/  Tolles DIY Video von OM Michael DL2YMR von der 100Watt PEP Version  

End Fed multiband antenna DIY kit for 10-15-20-40-80m 100Watt PEP SSBNew extended kit! This kit contains all the necessary components to build an EndFed 1:49 multiband antenna for the bands 10-15-20-40-80 meters up to 100 Watt PEP Phone. We have added a connection for the counterweight and the useful stainless steel ring etc. to the kit. This End Fed kit is supplied with the antenna wire of your choice: Standard antenna wire: This antenna wire consists of 1.0 mm2 fine stranded copper conductor with black PVC insulation. The total diameter is approx. 2 mm. Ideal for experiments or vacation antennas. As the core is only made of copper, this stranded wire will become slightly longer and therefore thinner over time. The tensile strength of this stranded antenna wire is limited. Copper/Kevlar stranded antenna wire This stranded antenna wire is specially manufactured for antennas. The stranded wire consists of a Kevlar core with approx. 1.1 mm2 tinned and fine-stranded copper conductors. 1x 0.4 mm Kevlar and 24x 0.25 mm copper. The sheathing is made of black UV-resistant PE. The total diameter is approx. 2.5 mm. The tensile strength is approx. 50 kg. You receive a strong, flexible and relatively light antenna strand. The kit contains the following components: 1x toroidal core FT-140-431x enameled copper wire GR2 for winding the toroidal core (1mm) approx. 1.00 meter1x polycarbonate housing with transparent cover 100x100x60 mm (IP67)1x mini insulator 65 * 15mm2x simplex terminals up to 2 mm wire (wire rope terminal) 1x thimble approx. 23.5 meter antenna wire 1mm² black 1x capacitor 100pF 2kV DC 1x PL259 panel jack 1x extension coil 110uH ready wound and measured 1x shrink tube black 25.4-12.7mm 1x various screws, washers and nuts made of stainless steel 1x stainless steel ring 3x Fast-On ring contactType: MultibandLength: approx. 23 meters Connection: PL Max. Power: 100Watt PEP Phone Weight: approx. 500g Balun 1:49

End Fed multiband antenna DIY kit for 10-20-40m 100Watt PEP SSBNew extended kit! This kit contains all the necessary components to build an EndFed 1:49 multiband antenna for the bands 10-20-40meters up to 100 Watt PEP Phone. We have added a connection for the counterweight and the useful stainless steel ring etc. to the kit. This End Fed kit is supplied with the antenna wire of your choice: Standard antenna wire: This antenna wire consists of 1.0 mm2 fine stranded copper conductor with black PVC insulation. The total diameter is approx. 2 mm. Ideal for experiments or vacation antennas. As the core is only made of copper, this stranded wire will become slightly longer and therefore thinner over time. The tensile strength of this stranded antenna wire is limited. Copper/Kevlar stranded antenna wire This stranded antenna wire is specially manufactured for antennas. The stranded wire consists of a Kevlar core with approx. 1.1 mm2 tinned and fine-stranded copper conductors. 1x 0.4 mm Kevlar and 24x 0.25 mm copper. The sheathing is made of black UV-resistant PE. The total diameter is approx. 2.5 mm. The tensile strength is approx. 50 kg. You receive a strong, flexible and relatively light antenna strand. The kit contains the following components: 1x toroidal core FT-140-431x enameled copper wire GR2 for winding the toroidal core (1mm) approx. 1.0 meters1x polycarbonate housing with transparent cover 100x100x60 mm (IP67)1x mini insulator 65 * 15mm2x simplex terminals up to 2 mm wire (wire rope terminal) 1x thimble approx. 23.5 meter antenna wire 1mm² black 1x capacitor 100pF 2kV DC 1x PL259 panel jack 1x extension coil 34uH ready wound and measured 1x shrink tube black 25.4-12.7mm 1x various screws, washers and nuts made of stainless steel 1x stainless steel ring 3x Fast-On ring contactType: MultibandLength: approx. 12 meters Connection: PL Max. Power: 100Watt PEP Phone Weight: approx. 550g Balun 1:49