Boni-Whip Active Antenna 20kHz - 300MHz Wide frequency range 20 kHz - 300 MHz Small dimensions  Ideal for traveling, at home or DX-Camps The BONI-WHIP active antenna replaces the very successful Mini-Whip antenna. Despite its size (only approx. 17 cm long), it renders excellent reception results on longwave, mediumwave and shortwave and additionally for VHF up to 300 MHz. We developed this antenna ourselves and it is built here in Germany, so it really is “Made in Germany” by Bonito. The antenna offers a lot of improvements and better values than the original Mini-Whip. In our newsroom you can see a benchmark test between the Boni-Whip vs. the Mini.Whip: http://newsroom.bonito.net Even on very low frequencies the Boni-Whip produces very good reception results. It can be used beginning with 20 kHz and is a good choice for listeners who are interested in low frequencies. We also thought about radio listeners who are interested in high frequencies and extended the range to 300 MHz. Even with only a little effort you can achieve fantastic reception results; and because of its small size, the antenna can be erected inconspicuously.  The active antenna circuitry is cased in a weather resistant box. The voltage supply is delivered by the antenna cable and the included power supply module.  Boni-Whip: As flexible as you Because of its interchangeable radiating elements (Whips) the Boni-Whip can be used with different elements for experiments. The antenna can thus be adjusted to the surrounding environment or a special reception area. Customer comment I have performed extensive outdoor tests on the Boni-Whip at various locations in Germany, Austria, and USA; and even I am amazed that we have produced an antenna with such small size, mobility and excellent performance/price ratio. You will get a noticeably better antenna for almost the same price as the original Mini-Whip. Boni-Whip: Quality made in Germany The electronics of the Boni-Whip are manufactured in Germany by an ISO9000-certified assembly company in industrial quality and assembled by us in the Bonito QTH. Technical data Boni-Whip Frequency range: 20 kHz -300 MHz Voltage supply: 12V-15V Gain: 3dB Upper Frequency Limit: (-1db): 300 MHz IP3: +32.5 dBm IP2: +55 dBm What's in the Box:  Boni-Whip active Antenna  Junction box  Whip / Radiator 5,5mm/2,1mm barrel DC power connector What else do i need? The Boni-Whip shortwave antenna is delivered without a coaxial cable, as everyone needs a different length. We offer you the right coaxial cables such as the H155 or the even better shielded Hyperflex 5 in different lengths. You need two coax cables: A coax cable between the Boni-Whip and the feeder with BNC plugs. In addition, another coaxial cable, from the feed switch (BNC plug) to your receiver. A stabilized 12V DC transformer power supply (no switching power supply!) Which can deliver approx. 150mA with a 5.5 / 2.1mm barrel connector is required for the power supply. The mast bracket, which is available in 28mm and 40mm, is useful for mounting on the mast etc. The OVP1000 surge arrester can also be useful for current weather events. To protect the BNC connector against weather influences, we offer a self-vulcanizing adhesive tape called NittoTape. If you want a little more amplification, you can also use the longer and flexible radiator, which brings approx 3 dB more level. Please note: The offered coaxial cables are custom-made and cannot be exchanged at a later date!Total length of the cable: cable cut +/- 3% + connector

Boni-Whip Marine Active Antenna 20kHz - 300MHz The Bonito Boni-Whip marine antenna is one of the smallest (only approx. 50cm long) long-, medium- and shortwave active antennas in the marine market. Despite its small size, it renders excellent reception. With its range of 20 kHz to 300 MHz,  the antenna covers both shortwave and FM. The antenna amplifier is directly integrated in the antenna and is powered by a power inserter requiring 12-15 V.  The circuit boards are multi- protected against corrosion and the bracket is made of stainless steel. The 2016 model has new housing and a new, longer and more flexible radiating element which results in signals which are stronger than before by 3dB. We only recommend on-board active antennas, in case you cannot use the aft stay or a long wire antenna because active antennas can often make interferences even stronger.  We tested many antennas and found a good compromise with this in-house development and at a good price at that. Tip: I recommend you order a roll of Nittotape (self-sealing adhesive tape) at the same time to product connections and to prevent corrosion.  Technical Data:Frequencyrange: 20kHz - 300MHz.Impedanz:  50 OhmPower supply:  12 Volt ca. 60mAPolarisation:  vertikal, omni Connection: BNCLenght:  ca. 50 cmWeight:  ca. 0,5 KgWorking temperature:  -10 bis 50 GradPole mount:  30-44 mm Scope of delivery:- Boni-Whip Marine Antenna- 12 - 15 Volt Bias Tee- 40cm flexible Whip- Stainless Steel bracket

GigActiv GA3005 Extreme Wideband Active Antenna Frequency range : 9 kHz - 3 GHz Power Supply: 5,5V - 12V Gain: + 3dB Upper Frequency Limit (-1db): 3000 MHz IP3: > +30 dBm typ. IP2: > +50 dBm typ. Where space is at a premium or you live in an area where an antenna is considered an undesirable element in neighborhood, the new GigActiv GA3005 is the ideal solution for the avid listener with a wide band receiver. The low noise GigActiv 3005 Extreme Wideband Active Antenna by NTi covers the whole frequency range from 9 kHz – 3 GHz. The antenna radiator measures only 10 cm (approx 4 inches) and so the unit can be mounted unobtrusively. The antenna requires a supply voltage of  5 –12V DC  (max. 120mA) fed through the coax cable via the standard supplied  DC interface CPI3000DP. It can also be powered via USB with slightly reduced performance. This is perfect for portable use in combination with a PC, which powers the antenna or the antenna can be powered autonomously and noise-free with a separate USB power bank. For shortwave and above 200MHz an IP3 of  typically > +30dBm is achieved. USB-powering possibleLarge supply voltage range of 5-12V. It can be powered either by a conventional plug power supply (5,5 / 2,1mm round plug) or via USB with a optional Cable. Autonomously and noise- free via a separate USB Power Bank as well. Whats in the Box?- GigActiv GA3005- Radiator- Junctionbox CPI3000UNI Dimesions incl Radiator:185 x 57 x 35mm  (7.28 x 2,24 x 1,38 inch) Made in Germany

MegActiv MA305FT Wide Band Active Antenna Wide frequency range 9kHz – 300MHz Small dimensions Dual Power Supply: 5,5V – 15V Selectable FM band stop filter with low pass function Ideal for traveling, at home or DX-Camps IP3:>typ. +30dBm / IP2:>typ. +50dBm Enlarged and flexible 200mm radiating element The new MegActiv MA305FT is an evolution of the popular MegActiv MA305. In addition to small improvements in electronics, the new MegActiv MA305FT has been equipped with a switchable FM band-stop filter. Thus, disturbing radiation from the FM band between 88 and 108 MHz can be easily minimized The new MegActiv MA305FT close the gap between the Boni-Whip and the GigActiv GA3005 E-Field Antennas. This low noise active antenna, which is produced according to the highest standards, covers the frequency range between 9kHz and 300MHz. With a radiating element of only 22 cm / 8,66 inch it can be erected inconspicuously. It can be powered with 5-15 V DC (max.10mA) and alternatively with the supplied Power unit CPI 1500DP via USB. Flexible FM-band stop filter Based on the well proven Megactiv platform, an additional low pass filter and a FM-band stop filter were integrated which can be activated or deactivated with a jumper. In case of FM-interferences, the FM bandstop filter can be activated with a jumper and so FM signals between 88 MHz and 108 MHz will be attenuated by 25 – 40 dB. Flexible power supply The MegActiv MA305FT can be operated by two different kinds of power sources. It can be powered either by a conventional plug power supply (5,5 / 2,1mm round plug) or via USB with a optional Cable. Powering via USB has the advantage that no external power supply is needed and that the antenna can be operated  autonomously and noise-free with a separate USB PowerBank. The supply voltage range is 5 - 15V DC (10mA max) and thus the antenna is also well suited for portable use. You want to test the MegActiv MA305FT live on air? If you would like to test the MegActiv MA305FT active antenna live, you can now conveniently do this over the Internet with a KIWI SDR. Just click on this Link and you can browse the whole band from 10kHz to 30MHz. The linked KIWI-SDR with a MegActiv MA305FT is located in Bonn (DL0DTM Clubstation Deutsche Telekom) and can handle up to 4 users at a time. Features Integrated double surge protection of the active components: Coarse protection by gas discharge tubes with 60V firing voltage with max. pulse leakage current 1kA (8/20µs) with additional integrated ESD fine protection of max. 2kV. Standard delivery with Power unit CPI1500DP (external power supply and USB-operation possible) IP3:>typ. +30dBm IP2:>typ. +50dBm Integrated double overvoltage protection of the active antenna part Integrated double surge protection of the active components: Coarse protection by gas discharge tubes with 60V firing voltage with max. pulse leakage current 1kA (8/20µs) with additional integrated ESD fine protection of max. 2kV. Fernando from Fenu-Radio.ch did the first comparison Test in Mai 2015 and released this test on his Page in German: www.fenu-radio.ch. Quote from the review by FenuRadio: (translated) "The NTi MegActiv is a small receiving antenna with excellent reception performance. The construction proved to be unproblematic, similar to the Boni-Whip. From VLF up on the FM band, the MegActiv receives very well despite their small size. When properly setup it provides a nearly unbeatable signal / noise ratio!" Whats in the box? MegActiv MA305FT Whip / Radiator Junction box CPI1500UNI Made in Germany Please note! The offered coax cables are custom-made and therefore not returnable / refundable.

OMG ?! This antenna will amaze you! The MegaDipole 300DX is a broadband active dipole with a maximum upper working frequency of 300 MHz. The dipole reacts to the electrical component (E-Field) of the electromagnetic field and will deliver best results regarding signal strength and SNR (signal -to-noise-ratio) at locations with little or no locally generated interference. Nonetheless, the receiver to be coupled to this antenna should have a high enough dynamic range so that it can effectively process the received signals. In contrast to simple E-field antennas with only one radiating element, the symmetrical construction of the MegaDipole 300DX, will result in almost no negative resonance effects or reflections caused by the coaxial cable. First choice for DXer The MegaDipol MD300DX is the ideal antenna for DXers. Particularly in electrically quiet environments, it can really play to its strength in efficiently amplifying weak signals. In practical operations, a maximum signal-to-noise ratio of 110dB was achieved! (see image ) Wideband With prodigious broadband capability and constant receive characteristics the MegaDipol MD300DX is ideal for wideband receivers, SDR's and WEB-SDR such as KiwiSDR etc. The MegaDipol MD300DX can of course also be operated on all other receivers, including lower-end SDRs and portable world receivers. Flexible power supply The MegaDipol is nominally supplied with 10 - 15V DC (max 40mA), however, it can be operated across a wide variety of supply voltages. The antenna can even be operated with slightly reduced IP values at the same gain with only 5 volts via USB. This offers a significant advantage in that you can supply the MegaDipol on trips away from the radio shack or DX expeditions autonomously, using a low-noise USB power-bank. "The MegaDipol has already attracted a lot of attention with its receive performance at various events such as DX-Camps, field days and in-house exhibitions. In these tests, the MD300DX surpassed the existing antennas usually by 10-15dB in the SNR." You want to test the MegaDipol MD300DX live on air? If you would like to test the MegaDipol MD300DX live, you can now conveniently do this over the Internet with a KIWI SDR. Just click on this Link and you can browse the whole band from 10kHz to 30MHz. The linked KIWI-SDR with a vertical MegaDipol MD300DX is in Ireland and can handle up to 4 users at a time. Customer Feedback"MegaDipol has arrived and installed. It seems to be a great antenna, especially compared to dimensions!" Technical data Frequency range: 9kHz - 300MHz IP3: typ. +30dBm (@7.00 & 7.20MHz) IP2: typ. +78dBm (@7.00 & 7.20MHz) Size/weight: 98 x 90 x 38mm / 0.12kg Whats in the Box? MegaDipol MD300DX Power Inserter CPI 1500UNI 2x 2.5m long radiating elements (PVC-coated, salt-water resistant stainless steel ropes) 2 insulators for installation (weatherproof plastic material with 4.5mm fixing hole) As noted previously, it is important that the connected receiver has a correspondingly high dynamic range in order to be able to optimally process the delivered signals. Recommendation Near the sea or in case of possible contact with salt water we strongly recommend the use of our weather protection case. Please note! The offered coax cables are custom-made and therefore not returnable / refundable.

MegaLoop FX Active Loop Antenna Probably the most flexible active loop antenna Ultra broadband frequency range from 9kHz - 180MHz High dynamic range with an IP of typ. +40 dB and IP 2 of typ. +85 dB Power requirements: 5V - 15V Selectable FM band stop filter with low pass function Selectable amplification in three steps Various radiating elements and sizes can be used Indoor and outdoor use Additional ground terminal (M5) on the enclosure High-quality craftsmanship; splash-water proof enclosure; all screw terminals made of stainless steel Small packaging = small shipping costs Ideal for outdoor use because dismountable and USB power supply The Megaloop FX is our latest active loop amplifier for the 9kHz to max. 180MHz range. It combines  all the outstanding features of the successful MegaLoop ML 200 and ML 052. Due to its integrated selectable FM band stop filter and the three-step amplification a maximum of flexibility for all kinds of use is possible. Flexible range of application This broadband magnetic loop antenna is especially suitable for places with difficult reception due to electrical interferences (E-field) in the near-field area, it is also made for indoor use or on the balcony/patio. You can put it up in the attic, at the window, on the balcony, in the carport fixed to the wall or permanently attached to a mast. Flexible FM-band stop filter Based on the well proven MegaLoop platform, an additional low pass filter and a FM-band stop filter were integrated which can be activated or deactivated with a jumper. In case of FM-interferences, the FM bandstop filter can be activated with a jumper and so FM signals between 88 MHz and 108 MHz will be attenuated by 25 - 40 dB. Flexible three-step amplification The gain of the MegaLoop FX can be adjusted in three steps by an internal jumper (High/Medium/Low)Frequency response (-3dB) and nominal amplification. a) FM-band stop off1. High Gain: 9 kHz - 110 MHz and 25 dB gain2. Medium Gain: 9 kHz - 150 MHz and 20 dB gain3. Low Gain: 9 kHz - 180 MHz and 15 dB gain b) FM- band stop on:1. High Gain: 9 kHz - 52 MHz and 25 db gain2. Medium Gain: 9 kHz - 60 MHz and 20 dB gain3. Low Gain 9 kHz - 66 MHz and 15 dB gain Flexible loop sizes The MegaLoop FX makes the most diverse radiating elements possible. As standard, a loop made of flexible PVC-coated and seawater-resistant (V4A) stainless steel wire is available. It comes as a 5m (16,40ft) circumference loop for indoor and portable as well as for outdoor use. Other lengths, such as 10m (32,81ft), are on offer. Even lengths up to 20m (65,62ft) have successfully been tested. Additionally, an aluminum rigid loop with a diameter of 40 cm or 80 cm is also available. Due to its versatility and adjustment of amplification, there will always be an ideal combination of the loop size and amplification. Excellent IP values with power supply as low as 5V With two signals in the 7 MHz range, an excellent IP3 value of typ. +40 dB and a IP 2 value of +85 dBm is achieved with mere 5 V ( max. 40mA) and so the loop can be powered via USB or power bank. A DualPower power inserter (bias tee) supply is included in the standard scope of delivery. The MegaLoop can be operated by two different kinds of power sources. It can be powered either by a conventional plug power supply (5,5 / 2,1mm round plug) or optional Cable via USB. Powering via USB has the advantage that no external power supply is needed and that the antenna can be operated independently and noise-free with a separate USB PowerBank. The supply voltage range is 5 - 15V DC (40mA max) and thus the antenna is also well suited for portable use. Integrated threefold surge protection of the active parts Coarse protection by gas arrester with 60V trigger voltage and a max. pulse leakage current of 1 kA (8/20µs) and by twofold additional integrated fine protection of max. 2 kV and 8 kV respectively. Additionally, the loop connections are connected to ground with high impedance to avoid static charges. Low shipping costs - no bulky item ! Since the antenna can be shipped as such a small parcel, there will only be standard postage and when ordering a rigid loop of 1m or 2m diameter you will already save about 35,-€ compared to shipping as a bulk item. Hint: With two suction cups you can attach the MegaLoop antenna to a window at home, in a hotel or when on the road. Because of its flexible loop, transportation is really a piece of cake. In our newsroom test " Design of a really portable SDR Part 2" I simply put the loop over the tailgate of our Caddy and was able to receive signals beautifully. You want to test the MegaLoop FX live on air? If you would like to test the MegaLoop FX live, you can now conveniently do this over the Internet with a KIWI SDR. Just click on this Link and you can browse the whole band from 10kHz to 30MHz. The linked KIWI-SDR with MegaLoop and 6,8 Meter Loop is located in northern Germany and can handle up to 4 users at a time. Scope of delivery MegaLoop FX 5m (16,40ft) PVC-coated, seawater-resistant stainless steel wire. Power inserter CPI 1500UNI Manual Made in Germany Recommendation Near the sea or in case of possible contact with salt water we strongly recommend the use of our weather protection case. Please note! The offered coax cables are custom-made and therefore not returnable / refundable.

 Paloran 200 passive Loopantenne Ultra-breitbandiger Frequenzbereich von 9kHz bis 200MHz Unterschiedliche Strahlerformen und Größen verwendbar Im Innen- und Außenbereich verwendbar Zusätzlicher Erdungsanschluss (M5) am Gehäuse Hochwertig verarbeitet; spritzwassergeschütztes Gehäuse, alle Schraubanschlüsse in Edelstahl ausgeführt Kleine Verpackung = günstige Versandkosten Die PALORAN 200 ist eine hochwertige, breitbandig angepasste, passive Loopantenne. Die Paloran stellt eine gute Alternative überall dort dar, wo genügend Platz zur Aufhängung vorhanden ist und gleichzeitig störungsarmer Empfang benötigt wird. Loopantennen sprechen im Nahfeldbereich (Abstand weniger als ca. 3 Wellenlängen) hauptsächlich auf die magnetische (H-Feld) Komponente des elektromagnetischen Feldes an. Dadurch wird der Empfang von hauptsächlich elektrischen (E-Feld) Störungen im Nahfeld stark unterdrückt, was sich besonders im unteren Frequenzbereich (VLF/Langwelle/Mittelwelle und unterem KW-Bereich) durch störungsärmeren Empfang positiv bemerkbar macht. Durch die rein passive Wirkungsweise benötigt die PALORAN 200 (aufgrund der höheren Schleifenlängen ab 15m Umfang) einen größeren Platzbedarf im Vergleich zu einer aktiven Loopantenne. Dafür erzeugt die Antenne aber keinerlei Intermodulationen oder andere intern generierte Störkomponenten, ebenso entfällt die Fernspeisung. Lieferumfang: Paloran 200 15 Meter Großschleife aus PVC-ummantelten, seewasserfestem Edelstahldrahtseil (V4A) 2 Stück Isolatoren Manual Was brauche ich sonst noch? Die Paloran 200 wird ohne Koaxialkabel ausgeliefert, da ja jeder eine andere Länge benötigt. Wir bieten Ihnen dazu die passenden Kabel wie das HF214UF oder Hyperflex 5 in unterschiedlichen Längen an. Sie benötigen zwei Koaxkabel: Ein Koaxkabel zwischen der MegaDipol MD300DX Aktivdipol und der Einspeiseweiche CPI1000DP mit BNC-Steckern. Dazu ein weiteres Koaxialkabel, von der Einspeiseweiche (BNC-Stecker) zu ihrem Empfänger. In Meeresnähe oder beim möglichen Kontakt mit Salzwasser, empfehlen wir dringend den Einsatz unseres Wetterschutzgehäuses. Der Überspannungsableiter OVP1000 kann bei den aktuellen Wettereignissen ebenfalls sinnvoll sein. Zum Schutz der BNC-Stecker gegen Witterungseinflüsse, bieten wir mit dem NittoTape ein selbstvulkanisierendes Klebeband an.

ALLMOPRAN 120 – Passive Allmode Receiving Antenna 20 kHz – 120 MHz Extremely wideband frequency range from 20 kHz to 120 MHz Compatible with different radiator types and sizes Inputs and output protected by fast 70V gas discharge arrestors Switchable input-side limiter (2 Vpp) Additional grounding terminal (M5) on the housing High-quality workmanship; splash-proof housing, all screw connections made of stainless steel Universal radiator set included: 2 × 7.5 m PVC-coated stainless steel wire rope Compact packaging = low shipping costs Universally configurable The ALLMOPRAN 120 from NTi is an innovative passive receiving antenna for demanding applications and a true all-rounder. It can be configured for connection with the following radiator types: Dipole (balanced) or End-fed (unbalanced) Loop (balanced or single-ended grounded) The ALLMOPRAN can therefore be configured for either H-mode or E-mode operation. Switching is done via a toggle switch, provided that the corresponding type of radiator is connected. The standard delivery includes a 2 × 7.5 m universal radiator set, allowing for a wide range of different radiator configurations. By combining high-quality transformer materials with a wideband matching network, operation is also possible in the VLF range – typically a weak spot for passive antennas. As a passive system, no additional power supply is required. The BNC connector socket is splash-proof and mounted in a durable, UV-stabilized polycarbonate housing with a transparent cover. Flexible adaptation to the local interference environment Electromagnetic waves consist of two different components in the near field: H or B (magnetic field strength vector) E (electric field strength vector) The near field is defined as a maximum distance of one wavelength; beyond that, far-field conditions apply. While the two field strength vectors are 90° out of phase in the near field, they are no longer separated in the far field. Since most sources of interference are found below 3 MHz, near-field conditions already apply at distances of less than 100 m. In such cases, it can make sense to prefer or suppress the E- or H-component in the near field. Depending on local conditions and interference sources, one or the other field component may provide better reception results. Want to test the ALLMOPRAN 120 live? You can now conveniently test the ALLMOPRAN 120 live on the Internet via a WEB-SDR. Simply click [this link], and you can explore the entire band from 20 kHz to 30 MHz. The linked WEB 888-SDR with the ALLMOPRAN in End-Fed mode and a total length of 21 m is located in Alsace (France). Up to 4 users can access it simultaneously. TECHNICAL DATA Optimal frequency range: 20 kHz – 120 MHz (–3 dB) Connector type & impedance: BNC / 50 Ohm Radiator connections: M5 thread (stainless steel) Output is DC-blocked (max. 50 V) Operating temperature range: –25°C to +45°C Size/weight: 105 × 105 × 50 mm / 0.2 kg Weather protection housing: splash-proof according to IPX2 (protected against dripping water at up to 15° tilt) Scope of delivery: ALLMOPRAN 120 in splash-proof weather housing Universal radiator set 2 × 7.5 m PVC-coated stainless steel wire rope Optional accessories: Mast mounting bracket Ground connection cable 155 mm, stainless steel wire rope, M5/M6 Manual (latest version available for download) FAQ The FAQ for the ALLMOPRAN can be downloaded [here].

This simple, lightweight travel loop is quick to deploy and the perfect companion for Airspy and similar SDR radios!   Most of the problems were related to ineffective RX antennas that were too sensitive to the surrounding noise. So we decided to design a new Noise Cancelling Passive Loop (NCPL) to fix the noise problem. The YouLoop is a generalization of the Möbius loop where a balanced electric shield is used as the centre of a multi-turn loop. The rest of the turns run inside the shield. To preserve this electric balance from alteration by the transmission line, a low loss miniature BALUN is used. The more turns, the higher gain at the lower frequencies. Note that to preserve the electric balance, the number of turns increases by increments of two. An aspect of this two-turns coax build is its response in VHF. The same HF magnetic loop can be used in the FM and the 2m HAM bands with a slight change of its core principle, it’s now a folded dipole. The feed point of the folded dipole is on the top and the actual legs are composed of the coax ground. In order to further improve the impedance matching and flatten the frequency response, a high impedance external pre-amplifier can be used near the antenna to present a constant output impedance to the receiver. This could be the best option for you if you do not want or cannot build the antenna from scratch. AS the only remaining action is to connect the SMA cables. Specification HF Response: 10kHz to 30 MHz VHF Response: up to 300 MHz Maximum Power: 250 mW No Tuning required Low-Loss Wide-Band BALUN with 0.28 dB loss typ. Dimensions: H-31cm x W-24cm x L-17cm Weight: 0.5kg

TECSUN AN-48x XL  Die Tecsun AN-48x XL ist eine tragbare Innenantenne mit aktiver Schleife (Loop) zum Empfang von Langwelle (LW), Mittelwelle (MW) und Kurzwelle (SW). Sie wurde speziell für Weltempfänger entwickelt. Diese Softloop bietet durch die mitgelieferten Kabel/Adapter umfangreiche Anschlussmöglichkeiten. An der mitgelieferten Controlbox lässt sich die Antenne bequem und individuell auf die Frequenz abstimmen (Frequency Tuning) und auch die gewünschte Verstärkung separat einstellen. Somit kann der Empfang auf Kurzwelle mit der AN-48x Loop deutlich verstärkt und abgestimmt werden. Das führt bei Weltempfängern zu einer klaren Empfangsverbesserung. Auch ideal für Unterwegs Durch die kompakten Abmessungen und den schnellen Aufbau ist die AN-48x XL Loop Antenne auch ideal für die Reise oder für die mobile Wellenjagd geeignet. Praxistipp Für eine optimale Nutzung empfehlen wir die AN-48x XL Softloop Antenne so zu befestigten, dass sie noch gedreht bzw. ausgerichtert werden kann. Damit können ggf. Störungen ausgeblendet bzw. das Nutzsignal verstärkt werden. Dazu empfehlen wir die Antenne an verschiedenen Standorten auszuprobieren. Frequenzbereiche LW: 120-400 kHzMW (AM): 520-1700 kHzSW: 3500-20000 kHz Tecsun AN-48x XL Ausführung im Detail Loopschleife mit Teleskopspreizer und Verstärker, sowie Bandumschalter Bedienteil (Controlbox) mit Ein-Aus-Schalter und Regler für Frequenzabstimmung und Verstärkungsregelung Verbindungsleitung Antenne-Bedienteil (jeweils 3,5mm Klinkenstecker) Adapter-Leitung - BNC (male) für Empfänger mit BNC Antennenbuchse Adapter-Leitung - CINCH (male) für Empfänger mit CINCH Antennenbuchse Adapter-Leitung – Krokodilklemmen, zum Anschluss an eine Teleskopantenne, für Weltempfänger die keinen externen Antennenanschluss für LW/MW haben. Ständer- gut geeignet, um den Ferritkoppler mit kleinen Radios zu verwenden Saugnapf zur Befestigung der Schleife an Fensterscheiben Clip zum Aufhängen Spreizer, damit das auch eine Schleife wird... Lieferumfang Loop Antenne Drei Anschlusskabel für Weltempfänger/Radios (für fast alle Gelegenheiten bzw. Empfänger) Ein Ferritkoppler für Lang- und Mittelwelle Ein Halter zum positionieren des Ferritstabes an ihrem Empfänger Deutsch- und englischsprachige Bedienungsanleitung  Wichtig Für den Betrieb benötigen 2 Akkus / Batterien (Micro AAA), die NICHT im Lieferumfang enthalten sind. Diese Antenne ist nicht für Sendebetrieb konzipiert.

End Fed multiband antenna DIY kit for 10-15-20-40-80m 300Watt PEP SSBNew extended kit! This kit contains all the necessary components to build an EndFed 1:49 multiband antenna for the bands 10-15-20-40-80 meters up to 300 Watt PEP Phone. We have added a connection for the counterweight and the useful stainless steel ring etc. to the kit. This End Fed kit is supplied with the antenna wire of your choice: Standard antenna wire: This antenna wire consists of 1.0 mm2 fine stranded copper conductor with black PVC insulation. The total diameter is approx. 2 mm. Ideal for experiments or vacation antennas. As the core is only made of copper, this stranded wire will become slightly longer and therefore thinner over time. The tensile strength of this stranded antenna wire is limited. LF Antenna Strand - New!This high-quality antenna strand consists of 32 individual 0.20 mm wires made of hard-drawn, bare copper. The conductor cross-section is approximately 1.0 mm² and offers excellent conductivity combined with high mechanical strength. It has a total diameter of 2.1 mm, a weight of approx. 11 g/m, and a breaking load of about 40 kg. The robust black polyethylene (PE) insulation reliably protects the strand from environmental influences and ensures a long service life. The kit contains the following components: 1x toroidal core FT-240-431x enameled copper wire GR2 for winding the toroidal core (1mm) approx. 1.50 meters1x polycarbonate housing with transparent cover 100x100x60 mm (IP67)1x mini insulator 65 * 15mm2x simplex terminals up to 2 mm wire (wire rope terminal) 1x thimble approx. 23.5 meter antenna wire 1mm² black 1x capacitor 100pF 2kV DC 1x PL259 panel jack 1x extension coil 110uH ready wound and measured 1x shrink tube black 25.4-12.7mm 1x various screws, washers and nuts made of stainless steel 1x stainless steel ring 3x Fast-On ring contactType: MultibandLength: approx. 23 meters Connection: PL Max. Power: 300Watt PEP Phone Weight: approx. 600g Balun 1:49Informationen gemäß Art. 19 GPSR Adresse des Herstellers: Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.netAdresse der verantwortlichen Person: Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net

End Fed multiband antenna DIY kit for 10-15-20-40-80m 100Watt PEP SSBNew extended kit! This kit contains all the necessary components to build an EndFed 1:49 multiband antenna for the bands 10-15-20-40-80 meters up to 100 Watt PEP Phone. We have added a connection for the counterweight and the useful stainless steel ring etc. to the kit. This End Fed kit is supplied with the antenna wire of your choice: Standard antenna wire: This antenna wire consists of 1.0 mm2 fine stranded copper conductor with black PVC insulation. The total diameter is approx. 2 mm. Ideal for experiments or vacation antennas. As the core is only made of copper, this stranded wire will become slightly longer and therefore thinner over time. The tensile strength of this stranded antenna wire is limited. LF Antenna Strand - New!: This high-quality antenna strand consists of 32 individual 0.20 mm wires made of hard-drawn, bare copper. The conductor cross-section is approximately 1.0 mm² and offers excellent conductivity combined with high mechanical strength. It has a total diameter of 2.1 mm, a weight of approx. 11 g/m, and a breaking load of about 40 kg. The robust black polyethylene (PE) insulation reliably protects the strand from environmental influences and ensures a long service life. The kit contains the following components: 1x toroidal core FT-140-431x enameled copper wire GR2 for winding the toroidal core (1mm) approx. 1.00 meter1x polycarbonate housing with transparent cover 100x100x60 mm (IP67)1x mini insulator 65 * 15mm2x simplex terminals up to 2 mm wire (wire rope terminal) 1x thimble approx. 23.5 meter antenna wire 1mm² black 1x capacitor 100pF 2kV DC 1x PL259 panel jack 1x extension coil 110uH ready wound and measured 1x shrink tube black 25.4-12.7mm 1x various screws, washers and nuts made of stainless steel 1x stainless steel ring 3x Fast-On ring contactType: MultibandLength: approx. 23 meters Connection: PL Max. Power: 100Watt PEP Phone Weight: approx. 500g Balun 1:49 Informationen gemäß Art. 19 GPSR Adresse des Herstellers:  Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net Adresse der verantwortlichen Person: Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net

End Fed multiband antenna DIY kit for 10-20-40m 300Watt PEP SSBNew extended kit! This kit contains all the necessary components to build an EndFed 1:49 multiband antenna for the bands 10-20-40meters up to 300 Watt PEP Phone. We have added a connection for the counterweight and the useful stainless steel ring etc. to the kit. This End Fed kit is supplied with the antenna wire of your choice: Standard antenna wire: This antenna wire consists of 1.0 mm2 fine stranded copper conductor with black PVC insulation. The total diameter is approx. 2 mm. Ideal for experiments or vacation antennas. As the core is only made of copper, this stranded wire will become slightly longer and therefore thinner over time. The tensile strength of this stranded antenna wire is limited. LF Antenna Strand - New!This high-quality antenna strand consists of 32 individual 0.20 mm wires made of hard-drawn, bare copper. The conductor cross-section is approximately 1.0 mm² and offers excellent conductivity combined with high mechanical strength. It has a total diameter of 2.1 mm, a weight of approx. 11 g/m, and a breaking load of about 40 kg. The robust black polyethylene (PE) insulation reliably protects the strand from environmental influences and ensures a long service life. The kit contains the following components: 1x toroidal core FT-240-431x enameled copper wire GR2 for winding the toroidal core (1mm) approx. 1.50 meters1x polycarbonate housing with transparent cover 100x100x60 mm (IP67)1x mini insulator 65 * 15mm2x simplex terminals up to 2 mm wire (wire rope terminal) 1x thimble approx. 23.5 meter antenna wire 1mm² black 1x capacitor 100pF 2kV DC 1x PL259 panel jack 1x extension coil 34uH ready wound and measured 1x shrink tube black 25.4-12.7mm 1x various screws, washers and nuts made of stainless steel 1x stainless steel ring 3x Fast-On ring contactType: MultibandLength: approx. 12 meters Connection: PL Max. Power: 300Watt PEP Phone Weight: approx. 600g Balun 1:49 Informationen gemäß Art. 19 GPSR Adresse des Herstellers:  Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net Adresse der verantwortlichen Person: Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net

End Fed multiband antenna DIY kit for 10-20-40m 100Watt PEP SSBNew extended kit! This kit contains all the necessary components to build an EndFed 1:49 multiband antenna for the bands 10-20-40meters up to 100 Watt PEP Phone. We have added a connection for the counterweight and the useful stainless steel ring etc. to the kit. This End Fed kit is supplied with the antenna wire of your choice: Standard antenna wire: This antenna wire consists of 1.0 mm2 fine stranded copper conductor with black PVC insulation. The total diameter is approx. 2 mm. Ideal for experiments or vacation antennas. As the core is only made of copper, this stranded wire will become slightly longer and therefore thinner over time. The tensile strength of this stranded antenna wire is limited.  LF Antenna Strand - New! This high-quality antenna strand consists of 32 individual 0.20 mm wires made of hard-drawn, bare copper. The conductor cross-section is approximately 1.0 mm² and offers excellent conductivity combined with high mechanical strength. It has a total diameter of 2.1 mm, a weight of approx. 11 g/m, and a breaking load of about 40 kg. The robust black polyethylene (PE) insulation reliably protects the strand from environmental influences and ensures a long service life. The kit contains the following components: 1x toroidal core FT-140-431x enameled copper wire GR2 for winding the toroidal core (1mm) approx. 1.0 meters1x polycarbonate housing with transparent cover 100x100x60 mm (IP67)1x mini insulator 65 * 15mm2x simplex terminals up to 2 mm wire (wire rope terminal) 1x thimble approx. 23.5 meter antenna wire 1mm² black 1x capacitor 100pF 2kV DC 1x PL259 panel jack 1x extension coil 34uH ready wound and measured 1x shrink tube black 25.4-12.7mm 1x various screws, washers and nuts made of stainless steel 1x stainless steel ring 3x Fast-On ring contactType: MultibandLength: approx. 12 meters Connection: PL Max. Power: 100Watt PEP Phone Weight: approx. 550g Balun 1:49 Informationen gemäß Art. 19 GPSR Adresse des Herstellers:  Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net Adresse der verantwortlichen Person: Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net

New extended kit! This kit contains all the necessary components to build an EndFed 1:649 multiband antenna for the bands 10-12-15-17-20-(30*)-40-80-160 up to 300 Watt PEP Phone. We have added a connection for the counterweight and the useful stainless steel ring etc. to the kit. This End Fed kit is supplied with the antenna wire of your choice: Standard antenna wire: This antenna wire consists of 1.0 mm2 fine stranded copper conductor with black PVC insulation. The total diameter is approx. 2 mm. Ideal for experiments or vacation antennas. As the core is only made of copper, this stranded wire will become slightly longer and therefore thinner over time. The tensile strength of this stranded antenna wire is limited. LF Antenna Strand - New!This high-quality antenna strand consists of 32 individual 0.20 mm wires made of hard-drawn, bare copper. The conductor cross-section is approximately 1.0 mm² and offers excellent conductivity combined with high mechanical strength. It has a total diameter of 2.1 mm, a weight of approx. 11 g/m, and a breaking load of about 40 kg. The robust black polyethylene (PE) insulation reliably protects the strand from environmental influences and ensures a long service life. The kit contains the following components: 1x toroidal core FT-240-431x enameled copper wire GR2 for winding the toroidal core (1mm) approx. 1.80 meters1x polycarbonate housing with transparent cover 100x100x60 mm (IP67)1x mini insulator 65 * 15mm2x simplex terminals up to 2 mm wire (wire rope terminal) 1x thimble approx. 23.5 meter antenna wire 1mm² black 1x capacitor 100pF 2kV DC 1x PL259 panel jack 1x extension coil 34uH ready wound and measured 1x shrink tube black 25.4-12.7mm 1x various screws, washers and nuts made of stainless steel 1x stainless steel ring 3x Fast-On ring contactType: Multiband 1:64 Length: approx. 46 meters Connection: PL Max. Power: 300/600Watts PEP Phone Weight: ca 600g Info The measurements for this antenna were made on two 12m spider beam masts, 10 meters above the ground, in an open field, without any buildings. Informationen gemäß Art. 19 GPSR Adresse des Herstellers:  Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net Adresse der verantwortlichen Person: Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net

Mini Endfed Antennenbausatz, für 10-20-40m mit Verlängerungsspule, max 100Watt PEP Die Mini Endfed ist eine kleine End Fed Antennen Lösung für den Portabeleinsatz,, auf Reisen, QRP, SOTA (Summit on the Air) oder DX Expeditionen usw. Das IP65 geschütze Gehäuse aus Polcarbonat, hat eine Größe von nur 64x58x35 mm und lässt sich leicht in der Tasche oder im Rucksack verstauen, ist aber auch robust genug für die stationäre Montage. Das Gewicht beträgt etwa 400-500 Gramm. Der Bausatz hat sowohl einen Anschluss für die ANTenne als auch GND für ein Gegengewicht. Den M4 Ring haben wir ebnso integriert. Damit lässt sich die Mini Endfed ganz einfach mit einem Karabiner befestigen und mit der Kausche als Zugentlasung vewenden. Alle Schrauben, Muttern und der Ring sind aus Edelstahl. Befestigt man die Antenne an der Spitze eines Teleskopmast, schiebt die Mastsegmente heraus, ist man innerhalb von wenigen Minuten auf Sendung! Um das Gehäuse des 1:49 Transformers an einem Mast zu befestigen, kann die gleiche Halterung wie von unseren Aktivantennen verwendet werden.  Dieser Mini Endfed-Bausatz wird mit einem Antennendraht Ihrer Wahl geliefert: Standard Antennenlitze:Diese Antennenlitze besteht aus 1,0 mm2 feindrähtiger Kupferleiter mit einer schwarzen PVC Isolierung. Der Gesamtdurchmesser beträgt etwa 2 mm. Ideal für Experimente oder Urlaubsantennen. Da der Kern nur aus Kupfer besteht, wird sich diese Litze mit der Zeit immer etwas längen und somit dünner werden. Die Zugfestigkeit dieser Antennenlitze ist begrenzt. LF-Antennenlitze - Neu! Diese hochwertige Antennenlitze besteht aus 32 Einzeldrähten à 0,20 mm aus hartgezogenem, blankem Kupfer. Der Leiterquerschnitt beträgt ca. 1,0 mm² und bietet hervorragende Leitfähigkeit bei gleichzeitig hoher mechanischer Festigkeit. Sie hat einen Gesamtdurchmesser von 2,1 mm, einem Gewicht von ca. 11 g/m und einer Bruchlast von etwa 40 kg. Die robuste Polyethylen-Isolation (PE) in schwarz schützt die Litze zuverlässig vor Umwelteinflüssen und sorgt für eine lange Lebensdauer In diesem Bausatz sind alle nötigen Bauteile zum Bau einer Mini EndFed Multiband Antenne für die Bänder 10-20-40 Meter bis100 Watt PEP Phone enthalten. Der Bausatz enthält die folgenden Bauteile:  ca. 12 Meter AntennendrahtVerlängerungsspule mit ca: 34uh (fertig gewickelt und vermessen)1x Edelstahl Kabelklemme1x Endisolator1x Kabelschuh 5mm1x Schrumpfschlauch 1:49 Mini Impedanztransformator: IP65-Gehäuse 64x58x35mm PolycarbonatRingkern FT140-43Kupferlackdraht GR2 Qualität 1,00 mm100 pF Kondensator 2kV1x BNC-Flanschbuchse2x M2,5 Schrauben 8/10mm2x M2,5 Mutter2x M2,5 Unterlegscheibe1x Kabelschuh 3mm3x M5 Kabelschuh2x Edelstahl M5 Schraube 20mm2x Edelstahl M5 Flügelmutter2x Edelstahl M5 Kragenmutter2x Edelstahl M5 Zahnscheibe2x Edelstahl M5 Schraube 20mm2x Edelstahl M5 Flügelmutter2x Edelstahl M5 Kragenmutter2x Edelstahl M5 Zahnscheibe1x Ring M41x Zahnscheibe M41x Mutter M41x Kabelkausche Die Bauanleitung finden Sie hier: ZUR BAUANLEITUNG    ** Die Bauanleitung bekommt gerade noch ihren Feinschliff

Mini Endfed antenna kit, max 100 watts for 10-15-20-40 meters approx. 20 meters long, without extension coil.The Mini Endfed is a small End Fed antenna solution for portable use, when travelling, POTA, QRP, SOTA (Summit on the Air) or DX expeditions etc. The IP65 protected housing made of polycarbonate with a size of only 64x58x35 mm can be easily stowed in a pocket or backpack, but is also robust enough for stationary mounting. The weight is around 400-500 grams, depending on the length of the antenna. If you attach the antenna to the top of a telescopic mast and slide out the mast segments, you can be on air within a few minutes! To attach the housing of the 1:49 transformer to a mast, the same bracket can be used as for our active antennas. This Mini Endfed kit is supplied with an antenna wire of your choice:Standard antenna wire: This antenna wire consists of 1.0 mm2 fine stranded copper conductor with black PVC insulation. The total diameter is approx. 2 mm. Ideal for experiments or vacation antennas. As the core is only made of copper, this stranded wire will become slightly longer and therefore thinner over time. The tensile strength of this stranded antenna wire is limited. Copper/Kevlar stranded antenna wire This stranded antenna wire is specially manufactured for antennas. The stranded wire consists of a Kevlar core with approx. 1.1 mm2 tinned and fine-stranded copper conductors. 1x 0.4 mm Kevlar and 24x 0.25 mm copper. The sheathing is made of black UV-resistant PE. The total diameter is approx. 2.5 mm. The tensile strength is approx. 50 kg. You receive a strong, flexible and relatively light antenna strand. These complete Mini End Fed Multiband kits are designed for 100 Watt PEP Phone and are available in these versions: 10-15-20-40 meters approx. 20 meters long, without extension coil 10-20-40 meters, approx. 12 meters long, with 34uH extension coil 10-15-20-40-80 meters, approx. 21 meters long with 110uH extension coilThe kit contains the following components: approx. 20.45 meters of antenna wire 1x stainless steel cable clamp 1x end insulator 1x cable lug 5mm 1:49 Mini Impedance transformer: IP65 housing 64x58x35mm polycarbonate Toroidal core FT140-43 Enameled copper wire GR2 quality 1.00 mm 100 pF capacitor 2kV 1x BNC flange socket 2x M2.5 screws 8/10mm 2x M2.5 nut 2x M2,5 washer 1x cable lug 3mm 3x M5 cable lug 2x stainless steel M5 screw 20mm 2x stainless steel M5 wing nut 2x stainless steel M5 collar nut 2x stainless steel M5 toothed washer 2x stainless steel M5 screw 20mm 2x stainless steel M5 wing nut 2x stainless steel M5 collar nut 2x stainless steel M5 toothed washer 1x ring M4 1x toothed washer M4 1x nut M4 1x cable thimbleYou can find the assembly instructions here: LINK Informationen gemäß Art. 19 GPSR Adresse des Herstellers:  Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net Adresse der verantwortlichen Person: Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net

Mini Endfed Antenna Kit for 10-15-20-40-80m, max 100 Watts PEP and 1:49 Transformer The Mini Endfed is a small endfed antenna solution for mobile use, travel, QRP, SOTA (Summit on the Air) or DX expeditions etc. The IP65 protected polar carbonate housing with a size of only 64x58x35 mm, can be easily stored in your pocket or backpack. The weight is about 250-500 grams, depending on the length of the spotlight. The kit has both a connector for the ANTenna and GND for a counter poise capacitance. We have also integrated the M4 ring. This makes it very easy to attach the Mini Endfed with a carabiner and use the thimble as a strain relief. All screws, nuts and the ring are made of stainless steel. If you attach the antenna to the top of a telescopic mast and slide out the mast segments, you are on the air within minutes! To attach the body of the 1:49 Transformer to a mast, you can use the same bracket as used by our active antennas. This End Fed Multiband Antenna comes with the antenna wire of your choice: Standard Antenna wire: This antenna litz wire is made of 1.0 mm2 fine stranded copper conductor with a black PVC insulation. The total diameter is about 2 mm. Ideal for experiments or vacation antennas. Since the core is only copper, this stranded wire will always elongate a bit over time, making it thinner. The tensile strength of this antenna strand is limited. Copper/Kevlar antenna litz wire This antenna litz wire is manufactured specifically for antennas. The litz consists of a Kevlar core with approx. 1.1 mm2 tinned and fine stranded copper conductors. 1x 0.4 mm Kevlar and 24x 0.25 mm copper. The jacket is made of black UV-resistant PE. The total diameter is approx. 2.5 mm. The tensile strength is approx. 50 kg. You will receive a strong, flexible and relatively light antenna litz wire. These complete Mini End Fed Multiband kits are designed for 100 Watt PEP Phone and are available in these configurations: 10-20-40 meters approximately 20 meters in length, without extension coil.10-20-40 meters, approx. 12 meters length, with 34uH extension coil10-15-20-40-80 meters, approximately 21 meters in length with 110uH extension coil. This kit contains: 23 meters of antenna wire19 mm PVC pipe with approx: 110uh coil1x stainless steel cable clamp1x end insulator1x cable lug 5mm1x heat shrink tubing 1:49 Mini impedance transformer:IP65 housing 64x58x35mm polycarbonateFerrite toroid Amidon FT140-43Winding wire 1,00 mm100 pF capacitor 1kV1x BNC flange socket2x M2,5 screws 8/10mm2x M2,5 nut2x M2,5 washer1x cable lug 3mm3x M5 cable lug2x stainless steel M5 screw 20mm2x stainless steel M5 wing nut2x stainless steel M5 collar nut2x stainless steel M5 lock washer2x stainless steel M5 screw 20mm2x stainless steel M5 wing nut2x stainless steel M5 collar nut2x stainless steel M5 tooth lock washer1x ring M41x tooth lock washer M41x nut M41x cable thimble You can find the building instructions here: TO THE CONSTRUCTION INSTRUCTION ** The construction manual is just getting its fine tuning

End Fed Multiband Antenna for 10-15-20-40-80m 300Watts PEP Phone You don't have time to build an Endfed Multiband Antenna? No problem. We offer you a ready assembled End Fed Multiband for the bands 10-15-20-40-80 meters up to 300 Watt PEP Phone. The antenna is tuned to band center. You only have to tune the antenna (as usual) minimally to the desired band section. This End Fed Multiband Antenna includes the following parts in addition to the standard components:Mounting plate, ring, thimble, ground connection, deluxe extension coil and a pressure equalization valve. This End Fed Multiband Antenna comes with: Copper/Kevlar antenna litz wire This antenna litz wire is manufactured specifically for antennas. The litz consists of a Kevlar core with approx. 1.1 mm2 tinned and fine stranded copper conductors. 1x 0.4 mm Kevlar and 24x 0.25 mm copper. The jacket is made of black UV-resistant PE. The total diameter is approx. 2.5 mm. The tensile strength is approx. 50 kg. You will receive a strong, flexible and relatively light antenna litz wire. Type: Multiband Length: approx. 23 meters Connection: PL Max. Power: 300Watt PEP Phone Weight: ca  650g Info The measurements for this antenna were made on two 12m spider beam masts, 10 meters above the ground, in an open field, without any buildings.

End Fed Multiband Antenna for 10-12-15-17-20-(30*)-40-80-1600m - 300Watts PEP Phone You don't have time to build an Endfed Multiband Antenna? No problem. We offer you a ready assembled End Fed Multiband for the bands 10-12-15-17-20-(30*)-40-80-160 meters up to 300/600Watts PEP Phone. The antenna is tuned to band center. You only have to tune the antenna (as usual) minimally to the desired band section. This End Fed Multiband Antenna includes the following parts in addition to the standard components:Mounting plate, ring, thimble, ground connection, deluxe extension coil and a pressure equalization valve. This End Fed Multiband Antenna comes with: Copper/Kevlar antenna litz wire This antenna litz wire is manufactured specifically for antennas. The litz consists of a Kevlar core with approx. 1.1 mm2 tinned and fine stranded copper conductors. 1x 0.4 mm Kevlar and 24x 0.25 mm copper. The jacket is made of black UV-resistant PE. The total diameter is approx. 2.5 mm. The tensile strength is approx. 50 kg. You will receive a strong, flexible and relatively light antenna litz wire. Type: Multiband 1:64 Length: approx. 46 meters Connection: PL Max. Power: 300/600 Watts PEP Phone Weight: ca 750g Info The measurements for this antenna were made on two 12m spider beam masts, 10 meters above the ground, in an open field, without any buildings. Informationen gemäß Art. 19 GPSR Adresse des Herstellers:  Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net Adresse der verantwortlichen Person: Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net

End Fed Multiband Antenna for 10*-15-20-40-80m 1000Watts PEP Phone You don't have time to build an Endfed Multiband Antenna? No problem. We offer you a ready assembled End Fed Multiband for the bands 10*-15-20-40-80 meters up to 1000 Watt PEP Phone. The antenna is tuned to band center. You only have to tune the antenna (as usual) minimally to the desired band section. This End Fed Multiband Antenna includes the following parts in addition to the standard components:3 instead 1 one ferrite core, Mounting plate, ring, thimble, ground connection, deluxe extension coil and a pressure equalization valve. This End Fed Multiband Antenna comes with: Copper/Kevlar antenna litz wire This antenna litz wire is manufactured specifically for antennas. The litz consists of a Kevlar core with approx. 1.1 mm2 tinned and fine stranded copper conductors. 1x 0.4 mm Kevlar and 24x 0.25 mm copper. The jacket is made of black UV-resistant PE. The total diameter is approx. 2.5 mm. The tensile strength is approx. 50 kg. You will receive a strong, flexible and relatively light antenna litz wire. Type: Multiband Length: approx. 23 meters Connection: PL Max. Power: 1000Watt PEP Phone Max Powaer digitaL: <100 Watts Weight: ca 1100g 10m needs a tuner Info The measurements for this antenna were made on two 12m spider beam masts, 10 meters above the ground, in an open field, without any buildings.

You don't have time to build an Endfed Multiband Antenna? No problem. We offer you a ready assembled End Fed Multiband for the bands 10-12-15-17-20-(30*)-40-80-160 meters up to 1000 Watts PEP Phone. The antenna is tuned to band center. You only have to tune the antenna (as usual) minimally to the desired band section. This End Fed Multiband Antenna includes the following parts in addition to the standard components:Mounting plate, ring, thimble, ground connection, deluxe extension coil and a pressure equalization valve. This End Fed Multiband Antenna comes with: Copper/Kevlar antenna litz wire This antenna litz wire is manufactured specifically for antennas. The litz consists of a Kevlar core with approx. 1.1 mm2 tinned and fine stranded copper conductors. 1x 0.4 mm Kevlar and 24x 0.25 mm copper. The jacket is made of black UV-resistant PE. The total diameter is approx. 2.5 mm. The tensile strength is approx. 50 kg. You will receive a strong, flexible and relatively light antenna litz wire. Type: Multiband 1:64 Length: approx. 46 meters Connection: PL Max. Power: 1000Watts PEP Phone Weight: ca 750g Info The measurements for this antenna were made on two 12m spider beam masts, 10 meters above the ground, in an open field, without any buildings. Informationen gemäß Art. 19 GPSR Adresse des Herstellers:  Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net Adresse der verantwortlichen Person: Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net

Mini End Fed Multiband Antenna You don't have time to build a Mini End Fed Multiband Antenna?No problem. We offer you a ready made Mini End Fed Multiband Antenna for the bands 10-15-20-40m or 10-15-20-40-80m up to 100 Watt PEP Phone. The antenna is tuned to band center. You only have to tune the antenna (as usual) minimally to the desired band area. The Mini Endfed is a small end fed antenna solution for mobile use, travel, QRP, SOTA (Summit on the Air) or DX expeditions etc. The IP65 protected polycarbonate case with a size of only 64x58x35 mm, can be easily stored in your pocket or backpack. The weight is about 400-500 grams, depending on the radiator length. This Mini End Fed antenna includes the following parts in addition to the standard parts: thimble, ground connection, deluxe extension coil. This End Fed Multiband Antenna comes with the antenna wire of your choice: Standard Antenna wire: This antenna litz wire is made of 1.0 mm2 fine stranded copper conductor with a black PVC insulation. The total diameter is about 2 mm. Ideal for experiments or vacation antennas. Since the core is only copper, this stranded wire will always elongate a bit over time, making it thinner. The tensile strength of this antenna strand is limited. Copper/Kevlar antenna litz wire This antenna litz wire is manufactured specifically for antennas. The litz consists of a Kevlar core with approx. 1.1 mm2 tinned and fine stranded copper conductors. 1x 0.4 mm Kevlar and 24x 0.25 mm copper. The jacket is made of black UV-resistant PE. The total diameter is approx. 2.5 mm. The tensile strength is approx. 50 kg. You will receive a strong, flexible and relatively light antenna litz wire. Technical dataType: MultibandLength: approx. 12 (10-40m) or 23 meters (10-80m)Connection: BNCMax. Power: 100Watt PEP PhoneWeight: approx. 250g   Informationen gemäß Art. 19 GPSR Adresse des Herstellers:  Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net Adresse der verantwortlichen Person: Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net

AntennaJet AAS300DP Aktiver 3-fach Antennenverteiler 9kHz - 300MHz (-450MHz*) Mit Dual Power! Großer Dynamikbereich Weiter Frequenzbereich: 9kHz - 300MHz (- 450MHz*) Hohe Intermodulationsfestigkeit Hohe Entkopplung der Ausgänge Hohe Rückwärts-Isolation Eingang ESD-geschützt Spannungsversorgung per USB oder Netzteil Made in Germany! Bonito's neuer Antennensplitter AntennaJet AAS300DP kann das Signal von einer Empfangsantenne auf bis zu 3 Empfänger nahezu ohne Verluste verteilen. Sein großer Frequenzbereich reicht von 9kHz - 300MHz (*mit kleinen Verlusten sogar bis 450MHz). Die interne Verteilung erfolgt über rauscharme, großsignalfeste Breitbandverstärker ohne gegenseitige Beeinflussung der Ausgänge. Der aktive Antennensignalverteiler AntennaJet AAS300DP verteilt ein Eingangssignal nahezu verlustlos an drei Ausgänge weiter. Bedingt durch die außerordentlich hohe Entkopplung der Ausgänge wird dabei eine gegenseitige Beeinflussung der angeschlossenen Empfänger vermieden. Ebenso wird dadurch die Abstrahlung von  möglicher Störstrahlung in Richtung Antenne wirkungsvoll unterdrückt. DualPower heißt: Stromversorgung per USB oder Netzteil Ab dem Modell 2017, lässt sich der AntennaJet AAS300DP Kurzwellen Antennenverteiler sowohl mit einem Netzteil (2,1mm Hohlstecker), als auch per USB mit Strom versorgen. Damit ist der AntennaJet noch flexibler geworden. Die USB-Versorgung hat den Vorteil, dass man A) kein externes Netzteil mehr braucht und B) den Antennensplitter auch autonom und rauscharm über eine separate USB-PowerBank versorgen kann. Durch die flexible Stromversorgung, dem geringen Stromverbrauch und seiner Kompaktheit ist der AAS300DP auch sehr gut portabel verwendbar. Es lassen sich bis zu max. drei Empfänger anschließen. Nichtangeschlossene Ausgänge können konstruktionsbedingt offen bleiben bzw. benötigen keinen Abschluss.Die Eingangsantennenbuchse ist mit einer ESD-Schutzschaltung gegen kurzzeitige bzw. pulsförmige Überspannungen und Überlastungen  geschützt.* * Der ESD Schutz ersetzt keinen Blitzschutz! Zur Montage des AntennaJets empfehlen wir unsere MB1 Halterung.  Technische Daten Eingangsfrequenzbereich: 9kHz - 300MHz (-1dB) (@ 450MHz -6dB)Eingangsbuchse/-impedanz: BNC / 50 Ohm (DC-geblockt max. 25V)ESD-Eingangsschutz: 30KV; max. Pulsleistung 350W (8/20µs)Max. zulässige Eingangsleistung: 0dBmDurchgangsdämpfung: max. 1.5dB typ.Ausgangssbuchsen/-impedanz: BNC / 50 Ohm (DC-geblockt max. 25V)Isolation zwischen den Ausgängen:70dB typ. <1MHz60dB typ. < 30MHz50dB typ. <100MHz35dB typ. <300MHzIsolation zwischen Ausgang und  Eingang (Rückwärts-Isolation):80dB typ. <1MHz70dB typ. <30MHz50dB typ. <100MHz35dB typ. <300MHz Amplitudendifferenz der Ausgänge:    max. 0.5dB typ.IP3 Intercept-Punkt dritter Ordnung:    +35dBm typ. <10MHz +20dBm typ. >100MHzStromversorgung: 5,5 – 12Volt DCAnschluss der Stromversorgung: USB-B Buchse oder 2,1mm HohlsteckerStromaufnahme: max.50mAArbeitstemperaturbereich: 0 - 40°C (ohne Betauung)Grösse / Gewicht: 115 x 90 x 32mm / 0.30kgKonformität: CE Optionales Zubehör:  Halterung MB1 USB A/B - Kabel (geschirmt mit Ferritkern) Bitte unbedingt  beachten: Der vorhandene ESD-Schutz ist nicht gleichbedeutend mit einem vollwertigen Blitzschutz; daher ist eine Haftung für angeschlossene Geräte grundsätzlich ausgeschlossen. Bei Nichtbenutzung, Abwesenheit, Sendebetrieb oder Gewittergefahr muss das Gerät immer von der angeschlossenen Antenne getrennt werden, um Schäden zu vermeiden.

Through Window or Door Connector Cable with BNC or PL connectors. Thourgh window cable Description: Flat coax cable, for feeding coax cables through windows and doors, For use with coax-cable. Saves drilling, for windows, doors,caravans and balconies.  Typ. insertation loss: up to 30MHz: <1dB up to 50MHz: < 2dB up to 75MHz: < 3.5dB up to 150MHz: <5dB Length with connectors: 30 cm (11,8") Length of the ribbon cable 20 cm (7,9") RX-Only!

Mast mounting for the rigid loop (MegaLoop) For a safe and stable mast mounting of the loop antenna, a rotation-free V2A stainless steel mast mounting set with a clamp is available. Because of the additional screw connection to a metal mast at the top of the loop, it is grounded at the same time.  The U-bolts  are in 28 mm or 40mm V2A vailable. 

This V4A mounting bracket fits for the Boni-Whip, MegActiv, GigActiv and the MegaLoop.

Flexible radiator M6 40cm long and flexible radiator with M6 stainless steel thread. Fits all MegActiv MA305 and Boni-Whip with M6 thread (Boni-Whip 2017 or later). This new radiator brings around 3dB more gain.

Flexible radiator M6 40cm long and flexible radiator with M6 stainless steel thread. Fits all MegActiv MA305 and Boni-Whip with M6 thread (Boni-Whip 2017 or later). This new radiator brings around 3dB more gain.

7,5  Volt plug AC Adapter Low noise unstabilizied 7,5  Volt max. 150mA plug power adapter with transformer (no switching power supply). 220/230 Volts only! This power supply is linear regulated and is no switching power supply. A "real" transformer is installed. Good for active antenna applications such as MegaLoop, MegActiv, MegaDipol and GigActiv. Input: 230V AC / 50Hz / 3,6 W Output: 7,5 V DC / max. 150 mA  (10,5 Volt idle) Dimensions without connectors: 75 x 55 x 60mm Weight: 100 grams Euro Plug Made in Germany