Der Problemlöser für 5mm Kabel mit N-Norm  Schwierige Position der Buchse am Gerät, die man nur mit einem Adapter lösen kann, dieser dann aber zu lang wird? Warum nicht gleich einen Winkelstecker auf das Kabel montieren? Dieser hochwertige N-Winkelstecker ist für die 5mm Koaxkabeltypen wie RG58U, RG58CU, RG142B/U, RG223U, RG400U, Aircell 5, Airborne 5, H 155, H 2005 und Hyperflex 5 geeignet. Er wird standardmäßig mit einer Masseverbindungshülse ausgeliefert.  Herstellernummer: UG 594-6 TA

Boni-Whip Active Antenna 20kHz - 300MHz Wide frequency range 20 kHz - 300 MHz Small dimensions  Ideal for traveling, at home or DX-Camps The BONI-WHIP active antenna replaces the very successful Mini-Whip antenna. Despite its size (only approx. 17 cm long), it renders excellent reception results on longwave, mediumwave and shortwave and additionally for VHF up to 300 MHz. We developed this antenna ourselves and it is built here in Germany, so it really is “Made in Germany” by Bonito. The antenna offers a lot of improvements and better values than the original Mini-Whip. In our newsroom you can see a benchmark test between the Boni-Whip vs. the Mini.Whip: http://newsroom.bonito.net Even on very low frequencies the Boni-Whip produces very good reception results. It can be used beginning with 20 kHz and is a good choice for listeners who are interested in low frequencies. We also thought about radio listeners who are interested in high frequencies and extended the range to 300 MHz. Even with only a little effort you can achieve fantastic reception results; and because of its small size, the antenna can be erected inconspicuously.  The active antenna circuitry is cased in a weather resistant box. The voltage supply is delivered by the antenna cable and the included power supply module.  Boni-Whip: As flexible as you Because of its interchangeable radiating elements (Whips) the Boni-Whip can be used with different elements for experiments. The antenna can thus be adjusted to the surrounding environment or a special reception area. Customer comment I have performed extensive outdoor tests on the Boni-Whip at various locations in Germany, Austria, and USA; and even I am amazed that we have produced an antenna with such small size, mobility and excellent performance/price ratio. You will get a noticeably better antenna for almost the same price as the original Mini-Whip. Boni-Whip: Quality made in Germany The electronics of the Boni-Whip are manufactured in Germany by an ISO9000-certified assembly company in industrial quality and assembled by us in the Bonito QTH. Technical data Boni-Whip Frequency range: 20 kHz -300 MHz Voltage supply: 12V-15V Gain: 3dB Upper Frequency Limit: (-1db): 300 MHz IP3: +32.5 dBm IP2: +55 dBm What's in the Box:  Boni-Whip active Antenna  Junction box  Whip / Radiator 5,5mm/2,1mm barrel DC power connector What else do i need? The Boni-Whip shortwave antenna is delivered without a coaxial cable, as everyone needs a different length. We offer you the right coaxial cables such as the H155 or the even better shielded Hyperflex 5 in different lengths. You need two coax cables: A coax cable between the Boni-Whip and the feeder with BNC plugs. In addition, another coaxial cable, from the feed switch (BNC plug) to your receiver. A stabilized 12V DC transformer power supply (no switching power supply!) Which can deliver approx. 150mA with a 5.5 / 2.1mm barrel connector is required for the power supply. The mast bracket, which is available in 28mm and 40mm, is useful for mounting on the mast etc. The OVP1000 surge arrester can also be useful for current weather events. To protect the BNC connector against weather influences, we offer a self-vulcanizing adhesive tape called NittoTape. If you want a little more amplification, you can also use the longer and flexible radiator, which brings approx 3 dB more level. Please note: The offered coaxial cables are custom-made and cannot be exchanged at a later date!Total length of the cable: cable cut +/- 3% + connector

End Fed multiband antenna DIY kit for 10-15-20-40-80m 300Watt PEP SSBNew extended kit! This kit contains all the necessary components to build an EndFed 1:49 multiband antenna for the bands 10-15-20-40-80 meters up to 300 Watt PEP Phone. We have added a connection for the counterweight and the useful stainless steel ring etc. to the kit. This End Fed kit is supplied with the antenna wire of your choice: Standard antenna wire: This antenna wire consists of 1.0 mm2 fine stranded copper conductor with black PVC insulation. The total diameter is approx. 2 mm. Ideal for experiments or vacation antennas. As the core is only made of copper, this stranded wire will become slightly longer and therefore thinner over time. The tensile strength of this stranded antenna wire is limited. LF Antenna Strand - New!This high-quality antenna strand consists of 32 individual 0.20 mm wires made of hard-drawn, bare copper. The conductor cross-section is approximately 1.0 mm² and offers excellent conductivity combined with high mechanical strength. It has a total diameter of 2.1 mm, a weight of approx. 11 g/m, and a breaking load of about 40 kg. The robust black polyethylene (PE) insulation reliably protects the strand from environmental influences and ensures a long service life. The kit contains the following components: 1x toroidal core FT-240-431x enameled copper wire GR2 for winding the toroidal core (1mm) approx. 1.50 meters1x polycarbonate housing with transparent cover 100x100x60 mm (IP67)1x mini insulator 65 * 15mm2x simplex terminals up to 2 mm wire (wire rope terminal) 1x thimble approx. 23.5 meter antenna wire 1mm² black 1x capacitor 100pF 2kV DC 1x PL259 panel jack 1x extension coil 110uH ready wound and measured 1x shrink tube black 25.4-12.7mm 1x various screws, washers and nuts made of stainless steel 1x stainless steel ring 3x Fast-On ring contactType: MultibandLength: approx. 23 meters Connection: PL Max. Power: 300Watt PEP Phone Weight: approx. 600g Balun 1:49Informationen gemäß Art. 19 GPSR Adresse des Herstellers: Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.netAdresse der verantwortlichen Person: Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net

POTA-FLEX 7 Koaxkabel Das neue POTA-FLEX 7 Koaxkabel wurde von Messi&Paoloni speziell für Outdoor-Anwendungen wie POTA (Parks on the Air), SOTA, IOTA etc. entwickelt, bei denen extrem robuste und gut sichtbare Koaxkabel gefragt sind. Die gelbe und reflektirende Ummantelung des Koaxkabels ist gut sichtbar und bietet somit auch an belebten Plätzen wie Parks tc. einen optischen Schutz und reduziert die Stolpergefahr und unbeabsichtigtem "Hängenbleiben". Das leichte und flexible Pota-Flex 7 Koaxialkabel von Messi e Paoloni hat einen Außendurchmesser von 7,65 mm, den Innenleiter bilden 19 einzelne Kupferdrähte. Die Abschirmung besteht aus 3 Schichten: 2 x Geflecht aus Kupferdraht mit jeweils 144 Drähten, darunter Kupferfolie mit einer PE-Schicht, die das Dielektrikum umgibt. Dadurch wird nicht nur eine ideale HF-Abschirmung erreicht, sondern das Kabel auch vor mechanischer Beschädigung geschützt.. Das Dielektrikum ist geschäumt, dadurch wird eine im Verhältnis zum Durchmesser sehr geringe Dämpfung erreicht. Technische Daten Pota-Flex 7 Impedanz @200Mhz: 50 Ohm ± 3 Minimaler Biegeradius: erfolgreich getestet bis zu 100 Biegungen, unter Verwendung des „PotaSpeed“ mit Innenkern Ø126mm Temperaturbereich: -40°C bis +60°C (-40°F bis +140°F) Kapazität: 75 pF/m ± 2 (22,9 pF/ft ± 2) Verkürzungsfaktor: 83% Abschirmungswirkungsgrad (SA) 100-2000 MHz >105 dB Innenleiterwiderstand: 7,3 Ohm/Km Außenleiterwiderstand: 12 Ohm/Km Spannungsprüfung (Funkentest): 4 kV Nettogewicht 100m (100ft): 5,4 Kg (3,63 lbs) Maximale Spitzenleistung: 8000 WATT Strukturelle Rückflussdämpfung: 0,3-600 MHz 600-1200 MHz 1200-2000 MHz >28 dB >22 dB >18 dB Informationen gemäß Art. 19 GPSRHersteller: Messi&PaoloniHerstellername: Messi & Paoloni SrlHandelsname: Messi & PaoloniAdresse: Via Giovanni Conti 1 - 60131 ANCONA, ItalyE-Mail: web@messi.itWebseite: https://messi.it/ Verantwortliche Person:Name: Messi & Paoloni SrlAdresse: Via Giovanni Conti 1 - 60131 ANCONA, ItalyE-Mail: web@messi.itWebseite: https://messi.it/

Weatherproof housing for MegaLoop and MegaDipol This UV-protected and ventilated polycarbonate case protects your MegaLoop (all models since 2014) or MegaDipol from heavy rainfall and other extreme weather conditions like a second skin. A sliding stainless steel sleeve additionally protects the drain on the BNC connector. The screw connections for the radiating elements and grounding are led through to the outside and are also made of stainless steel. When operating in salty environments and near the sea, the weatherproof housing should definitely be used additionally. Our antennas are designed to be splash-proof, but salty capillary water can conquer even the best sealing gasket over time. The rear ventilated weatherproof housing effectively prevents direct contact of the antenna electronics with harmful weather influences.   Assembly Instructions You can find assembly instructions here: LINK

Mini Endfed Antenna Kit for 10-15-20-40-80m, max 100 Watts PEP and 1:49 Transformer The Mini Endfed is a small endfed antenna solution for mobile use, travel, QRP, SOTA (Summit on the Air) or DX expeditions etc. The IP65 protected polar carbonate housing with a size of only 64x58x35 mm, can be easily stored in your pocket or backpack. The weight is about 250-500 grams, depending on the length of the spotlight. The kit has both a connector for the ANTenna and GND for a counter poise capacitance. We have also integrated the M4 ring. This makes it very easy to attach the Mini Endfed with a carabiner and use the thimble as a strain relief. All screws, nuts and the ring are made of stainless steel. If you attach the antenna to the top of a telescopic mast and slide out the mast segments, you are on the air within minutes! To attach the body of the 1:49 Transformer to a mast, you can use the same bracket as used by our active antennas. This End Fed Multiband Antenna comes with the antenna wire of your choice: Standard Antenna wire: This antenna litz wire is made of 1.0 mm2 fine stranded copper conductor with a black PVC insulation. The total diameter is about 2 mm. Ideal for experiments or vacation antennas. Since the core is only copper, this stranded wire will always elongate a bit over time, making it thinner. The tensile strength of this antenna strand is limited. Copper/Kevlar antenna litz wire This antenna litz wire is manufactured specifically for antennas. The litz consists of a Kevlar core with approx. 1.1 mm2 tinned and fine stranded copper conductors. 1x 0.4 mm Kevlar and 24x 0.25 mm copper. The jacket is made of black UV-resistant PE. The total diameter is approx. 2.5 mm. The tensile strength is approx. 50 kg. You will receive a strong, flexible and relatively light antenna litz wire. These complete Mini End Fed Multiband kits are designed for 100 Watt PEP Phone and are available in these configurations: 10-20-40 meters approximately 20 meters in length, without extension coil.10-20-40 meters, approx. 12 meters length, with 34uH extension coil10-15-20-40-80 meters, approximately 21 meters in length with 110uH extension coil. This kit contains: 23 meters of antenna wire19 mm PVC pipe with approx: 110uh coil1x stainless steel cable clamp1x end insulator1x cable lug 5mm1x heat shrink tubing 1:49 Mini impedance transformer:IP65 housing 64x58x35mm polycarbonateFerrite toroid Amidon FT140-43Winding wire 1,00 mm100 pF capacitor 1kV1x BNC flange socket2x M2,5 screws 8/10mm2x M2,5 nut2x M2,5 washer1x cable lug 3mm3x M5 cable lug2x stainless steel M5 screw 20mm2x stainless steel M5 wing nut2x stainless steel M5 collar nut2x stainless steel M5 lock washer2x stainless steel M5 screw 20mm2x stainless steel M5 wing nut2x stainless steel M5 collar nut2x stainless steel M5 tooth lock washer1x ring M41x tooth lock washer M41x nut M41x cable thimble You can find the building instructions here: TO THE CONSTRUCTION INSTRUCTION ** The construction manual is just getting its fine tuning

SIVA RF 400 UF-PVC low loss Koaxialkabel 10,3 mm Das RF400 UF ist eine sehr gute Alternative in der 10,3mm Koaxialkabelklasse und für den Frequenzbereich bis 3 GHz geeignet. Dieses doppelt geschirmte Koaxkabel, hat eine geringe Dämpfung und gute Flexibilität. Der Innenleiter wird aus 7x1mm Drähten gefertigt. Das Geflecht, umschließt die kunststoffbeschichtete Kupferfolie, mit einem Bedeckungsgrad von 78%.  Die gravierenden Unterscheide zu einem RG58U, haben wir in einem Artikel ausführlich, mit vielen realen Beispielen beschrieben: zum Artikel Eigenschaften Sehr flexibel Für Rotorbetrieb geeignet Innenleiter mit 7 Drähten (7x1mm) Für Frequenzen bis 3 GHz geeignet UV-beständig Es können viele RG-213 übliche Antennenstecker genutzt werden. Schirmung: > 80dB (100-900 MHz)> 70dB (900-2000 MHz)> 60dB (2000-3000 MHz) Kabelaufbau: Innenleiter: Kupfer, 7x1,0 mm, Ø 2,9 mm ± 0,05Dielektrikum: PE geschäumt, PEG Ø 7,3 mmAußenleiter 1: Kupferfolie, kunststoff beschichtetAußenleiter 2: Kupfergeflecht, opt. Bedeckung 73%, 112 Drähte Außenhaut: PVC, hoch flexibel, Ø 10,2 mm ± 0,15 mm UV-resistent Kabelgewicht: Kilogram per Kilometer: Kupfer: 81.0 kg / km Kunststoff: 63.8 kg / km Gesammt: 144.8 kg / km Dämpfung bei 20°C (dB x 100 meters) 5 MHz - 1.1dB10 MHz - 1.5dB50 MHz - 2.9dB200 MHz - 6.0dB500 MHz -10.3dB800 MHz - 13.2dB1000 MHz - 15.0dB3000 MHz - 28.1dB Komplettes Datenblatt: DownloadInformationen gemäß Art. 19 GPSR SI.VA SRL - Via Vittorio Veneto, 63 - 24040 Bonate Sotto (Bergamo) Italy Tel. 035 991085/86 - siva@sivacavi.it - https://sivacavi.it/ Verantwortliche Person: SI.VA SRL - Via Vittorio Veneto, 63 - 24040 Bonate Sotto (Bergamo) Italy Tel. 035 991085/86 - siva@sivacavi.it - https://sivacavi.it/

The Messi & Paoloni MP-CO.UHF.7M-S-EVO is a UHF Male (PL259) solder enhanced connector for 7.3mm / .287" cables. Genuine Messi & Paoloni enhanced solder connector UHF Male (PL259) 2-Pack Compression design with double seal to ensure better protection against infiltration of water, humidity and condensation Easy installation and welding instructions included in the package (no braid soldering needed) Dramatic suppression of the background noise, improvement of screening attenuation and insertion losses The UHF Evolution can be used up to 6000 MHz, a well made PL259 is barely acceptable up to 2000 MHz Model MP-CO.UHF.7M-S-EVO Product dimensions: 0.82 x 1.81 in. (2.1cm x 4.6cm) Wrench size: 0.63 in (16mm) For ULTRAFLEX 7 /.287'' cable Note: The new designed pin prevents excess of tin and the consequent heating, which damages the dielectric causing an uncontrollable alteration of the electrical properties of your cable.

Our special heat shrink tube with MIL and UL approval. The inside is coated with an extremely adhesive hot melt adhesive. Due to the heating during the shrinking process, the adhesive melts and reliably fills all edges and bumps. In this way, a waterproof sheathing is achieved. We use these heat shrink tubing on all our cable assemblies for H155, Hyperflex 5 and Ultraflex 7 coaxial cables. The shrinkage rate is approximately 3: 1. The required shrink temperature is 120°C. Continuous temperature resistance: - 55°C to + 110°C Use Electrical insulation, tabs, coaxial connectors, screwed connections Technical information Length: 30cm (11,8 inch) per bar Diameter: 18mm Standard color: black Flammability: self-extinguishing Handling When cutting, make sure you have smooth cut edges. Always start shrinking at one end. Select the highest possible shrink temperature.

Messi & Paoloni Hyperflex 5 Crystal Low-Loss coax cable A new breakthrough in the market  standards! The new international reference point for attenuations, flexibility and screening efficiency for all 5,4mm/0,212'' cables!  Best in its class Extreme flexibility:  perfect matching with rotator operated antennas, obtained by means of a sophisticated full copper stranded inner conductor (19 wires instead of 7).New improved dielectric: outstanding attenuations up to 6 Ghz, even better than some solid core cables of the competition.  Screening efficiency:  >105 dB (SA) and improved sturdiness reached by adding 24 more wires to the braid, for a total of 120 wires, (88% coverage+ 100% foil). This leads to a dramatic reduction of the background noise. Moreover the braiders used are 24 spools, instead of 16 spools, giving 50% MORE CROSSOVERS.Lightweight:  4,4 Kg/100 m  for a reduced stress of the “hanging and swinging" stretch of the cable in rotor operated antennas. Excellent Power Handling! The external PVC jacket is in black UV resistant PVC. Useful hint: the PVC used for the jacket of the cables, makes them extremely flexible but it's not suitable for underground laying. Every cable can be made with PE jacket, on specific request and for reasonable quantities in order to make them buriable. ATTENUATION at 20°C FREQUENCY dB/100m dB/100ft1,8 MHz 1,48 0,453,5 MHz 1,91 0,587,0 MHz 2,33 0,7110 MHz 2,63 0,8014 MHz 3,04 0,9321 MHz 3,64 1,1128 MHz 4,16 1,2750 MHz 5,58 1,70100 MHz 8,02 2,44144 MHz 9,66 2,94200 MHz 11,44 3,49400 MHz 16,37 4,99430 MHz 17,0 5,18800 MHz 23,48 7,161000 MHz 26,46 8,071296 MHz 30,5 9,302400 MHz 42,58 12,983000 MHz 48,1 14,664000 MHz 56,95 17,365000 MHz 65,29 19,906000 MHz 72,92 22,23