N- Stecker EVO 5,0mm Messi & Paoloni

Special scissors for cables specifically designed by Messi & Paoloni for ensuring a great accuracy in the cutting of each cable layers.  This cable scissor cuts cables 12mm like: RG58, H 155, Hyperflex 5, Ultraflex 7, Hyperflex 10, RG213 and many more. We use these cable scissors ourselves and cut all cables with it. It lays very good in the hand and you just have in the best control and feel the different layers of the coaxial cable and can cut exactly the desired part of the cable. This cable scissor from Messi and Paoloni is our recommendation to our customers 

Airborn 5 AIRBORNE 5 /.200" [5 mm / 0,197 inches Cable] WHY CHOOSE THIS CABLE?: Same dimensions of a RG 58 C/U (5mm) but at 50 MHz its attuenuation is 3,6 dB/100m better. Perfect for direct burial and totally waterproof thanks to the PE carbon-black tearproof sheath that allow different kind of outdoor uses. Weights 1,4 Kg less per 100m than RG 58: its incredible lightness will prove a great operational advantage and will ensure significant savings in shipping costs and "DXpedition". It's only 5mm of diameter but Airborne 5, made with tough aluminium magnesium alloy braid, boasts a superlative robustness and enviable resistance. Attenuation (20°C /68°F) FREQUENCY dB/100m 1,8 MHz       1,7 3,5 MHz       2,3  7 MHz          3,0  10 MHz        3,4 14 MHz        4,0 21 MHz        4,8 28 MHz        5,5 50 MHz        7,1 100 MHz      9,4 144 MHz    11,1 200 MHz    12,8 400 MHz    18,3 430 MHz    19,0 800 MHz    26,5 1000 MHz    29,8 1296 MHz    34,2 2400 MHz    47,5 3000 MHz    53,5 4000 MHz    61,0 5000 MHz    68,6 6000 MHz    75,6

RG58 CU MIL-C-17G Koaxialkabel made in Italy by SIVA Cavi Dieses RG58 CU ist ein flexibles und preiswertes Koaxialkabel aus dem Hause SIVA. Es kommt aus Italien und entspricht dem höchsten UL-Standard MIL C 17 "G". Das Kabel besitzt eine Kupferlitze verzinnt als Innenleiter. Der Außenleiter aus verzinntem Kupfergeflecht, mit 112x0,13mm Drähten, einer Abdeckung von 94% und einer Schirmung von >57dB.  Aufbau Innenleiter 19 x 0,18 mm CU SN CU SN = Kupfer verzinnt Isolation 2,95 mm PE ± 0,1 Außenleiter Cu-Geflecht verzinnt, mit 112 x 0,13mm Drähten und 95%Abdeckung Mantel 5mm PVC2 schwarz ± 0,2 Bruchlast 139 N Biegeradius min. 25 mm Kupferzahl 18,7 kg/km Temperaturbereich -30°C bis +70°C Elektrische Daten Impedanz 50 Ohm ± 3 Kapazität 100 pF/m Verkürzungsfaktor 0,66 Schleifenwiderstand 53 Ohm/km Schrimung; bis 900MHz >57dBInformationen gemäß Art. 19 GPSR SI.VA SRL - Via Vittorio Veneto, 63 - 24040 Bonate Sotto (Bergamo) Italy Tel. 035 991085/86 - siva@sivacavi.it - https://sivacavi.it/ Verantwortliche Person: SI.VA SRL - Via Vittorio Veneto, 63 - 24040 Bonate Sotto (Bergamo) Italy Tel. 035 991085/86 - siva@sivacavi.it - https://sivacavi.it/

Why should the use of M&P-Flux always be considered?The M&P-Flux is now the faithful companion of all the specialized technicians involved in soldering on printed microcircuits.It can be used in a very convenient way both in the soldering phase and in the desoldering phase, due to the following reasons.Improvement of thermal conductivity and capillarity: Its chemical composition facilitates the entry of molten tin, causing it to be sucked by "capillarity" inside the hole in the UHF EVO pins, or the N pins or PL259 connectors and any other solder connector.This occurs by leaving the outer surface of the pin, clean and therefore free of unwanted accumulations of solder. The capillarity phenomenon described above generates greater welding speed, which results in less thermal stress for the dielectric of the coaxial cable which could deform due to too much prolonged heat. The resulting welding is never cold and opaque, but shiny and reliable, in a shorter time To unsolder instead, using the desoldering braid combined with M&P-Flux while heating the interested parts with the soldering iron, we will see an inverse effect of the tin flow which this time, always aspirated by capillarity, as if by magic, will be attracted by the desoldering braid, leaving the connector clean and perfectly reusable. M&P-Flux should be applied with the special mini tube dispenser inside the hole, in small quantities. Then place the tin wire, and the tip of the soldering iron at the temperature of 300 ° -350 ° C. (572 ° -662 ° F.). The soldering will run exactly where it is needed avoiding short circuits, and saving you time and hassle.IMPORTANT NOTICE: as for every product of this kind, it is essential to keep out of the reach of children. The product is harmful if swallowed, causes skin irritation or severe eye irritation if in contact. In case of eye contact wash immediately and call a specialist. Wash your hands thoroughly after use or better use latex gloves instead. Use in an open or ventilated place, or drain the fumes with a suitable suction system. All these precautions apply to every soldering activity (solder may be composed by 30-40% lead, while M&P Flux is ROHS Compliant - Lead Free, therefore as it reduces the soldering time, you’re less exposed to the tin-lead fumes).Informationen gemäß Art. 19 GPSR Hersteller: Messi&Paoloni Herstellername: Messi & Paoloni Srl Handelsname: Messi & Paoloni Adresse: Via Giovanni Conti 1 - 60131 ANCONA, Italy E-Mail: web@messi.it Webseite: https://messi.it/ Verantwortliche Person: Name: Messi & Paoloni Srl Adresse: Via Giovanni Conti 1 - 60131 ANCONA, Italy E-Mail: web@messi.it Webseite: https://messi.it/