Antenna wire SL - SuperLight

€0.64*

Content: 1 Laufende(r) Meter

Available, delivery time: 2-5 days

Product number: 0430

Product information "Antenna wire SL - SuperLight"

Antenna wire SL - SuperLight

The super-light and high-strength stranded antenna wire is specially manufactured for use as long wire, end-fed, dipole or other antennas. The antenna strand is only 1.6 mm thick and consists of 6x0.25 mm tinned copper braiding. It has a core of tear-resistant Vectran fibers® and a weatherproof PE insulation. This gives it a maximum breaking load of up to 60kg! The low weight of only 4g per meter makes it ideal for mobile operation, DX expeditions SOTA, IOTA, COTA or POTA.

Super light antenna wire

Weight only about 4g/m
6x0.25mm copper braid, tinned
Core made of Vectran fibers®
Cross-section approx. 0.3 mm2
Insulation made of waterproof PE (polyethylene), black
Diameter: 1.6 mm
Maximum breaking load approx. 60 kg

Accessory Items

End Fed 1:9 UNUN 600/1200W

1:9 UNUN transformer for the frequency range: 1-30MHz and a maximum transmission power of either 600W or 1500W PEP. The IP67 housing is of course made of UV-resistant polycarbonate. Including connection for a counterweight and, for market launch, with mast mounting shown. All screws and nuts are made of stainless steel. The PL or N sockets used are high quality and PTFE dialectic. A tuner is required for non-resonant antennas. The following wire lengths have proven to be useful:6.5m - 6.9m - 13.5m - 13.9m - 16.2m - 20.8m - 22m - 26m - 27.7m - 34.7m - 41.6m - 48.5m - 55.5m You can find suitable antenna strands here: Copper Kevlar stranded wire Translated with DeepL.com (free version)

From €140.00*

Details

Similar Items

Antennenlitze 1,0 mm² für End Fed Antennen

Antenna litz wire 1.0 mm²

Antenna wire 1.0 mm² (outer diameter 2.48mm), black for End Fed antennas. Price per Meter

€0.39*

Dipoflex special copper wire for dipoles

Dipoflex antenna wire is highly suitable for the coinstruction of wire antennas. It combines high strength with excellent conductivity and low weight. The braided conductor is made of 19 single copper strands, that is a much higher number than on comparable products. The larger number of strands leads to a larger surface area, very important for the conductivity of high frequency currents (skin effect). The tensile strength is high due to the selection of the copper alloy. The black polyurethane sheath is boosted with UV resistant ingredients to achieve a good long term stability under adverse weather conditions. Dipole antenna wire, made of pure copper geometrically stranded. Conductor: Copper 19 X 0,29mm (19 X 0.011 in) Diameter: 1,45 mm (0.057 in) Section: 1,25 sq.mm (0.0019 in2) Electrical resistance: 15 Ohm/Km (4.6 Ohm/1000ft) Sheath: PE black with UV filter Diameter: 2.20 mm (0.086 in) Tear resistance: 45 Kg (99.2 lb) Weight: 1,338 Kg/100m (2.95 lb/100ft)

€0.89*

Details

Copper/Kevlar Antenna Wire

Copper/Kevlar Antenna Wire This antenna litz wire made of copper/Kevlar, is specially manufactured in the Netherlands for use as long wire, endfed, dipole or other antennas. The wire consists of a Kevlar core with approx. 1.1 mm2 tinned copper braid. The combination of Kevlar and copper gives an optimal mix of RF wire and tensile strength of about 50kg. In contrast to the pure copper braid, the length remains stable here, because the braid does not elongate over time. Thus, frequency and SWR remain stable over a long time. The insulation is made of high quality and UV-resistant PE. This antenna wire is therefore durable, strong, still flexible and has with only 14g per meter, a low weight. Ideal for travel (SOTA, IOTA; etc) but also perfect for a permanently installed antenna. Specifications: 1x 0,4 mm Kevlar core 24x 0.25 mm tinned copper. Copper section: 1.2 mm2 Weight: 14 grams per meter UV resistant black PE insulation Total diameter +/-2,5 mm Tensile force approx. 50kg

From €0.95*

Details