Hamrope PES 4

Duplex rope clamp suitable for e.g. Hamrope PES 4 with diameter up to 4 mm Material: A2 stainless steel

Duplex cable clamp suitable for antenna wire up to 2 mm in diameter. Material: A2 stainless steel

Rope clamp Clamcleat® CL260 - pack of 10 pieces Self-locking rope clamps made of high-strength, UV and cold-resistant material (tested in arctic conditions). Easily adjustable and retightenable at any time. For ropes of 2-4mm diameter. Ideal for Hamrope PES4. Material: nylon, color olive green or black, supplied in a pack of 10.

Stainless steel (A4) Cable thimble suitable for antenna wire with a diameter of 2mm

Simplex cable clamp suitable for antenna wire with a diameter of up to 3 mm Material: Stainless steel (Inox) A2

Mini Endfed Antenna Kit for 10-15-20-40-80m, max 100 Watts PEP and 1:49 Transformer The Mini Endfed is a small endfed antenna solution for mobile use, travel, QRP, SOTA (Summit on the Air) or DX expeditions etc. The IP65 protected polar carbonate housing with a size of only 64x58x35 mm, can be easily stored in your pocket or backpack. The weight is about 250-500 grams, depending on the length of the spotlight. The kit has both a connector for the ANTenna and GND for a counter poise capacitance. We have also integrated the M4 ring. This makes it very easy to attach the Mini Endfed with a carabiner and use the thimble as a strain relief. All screws, nuts and the ring are made of stainless steel. If you attach the antenna to the top of a telescopic mast and slide out the mast segments, you are on the air within minutes! To attach the body of the 1:49 Transformer to a mast, you can use the same bracket as used by our active antennas. This End Fed Multiband Antenna comes with the antenna wire of your choice: Standard Antenna wire: This antenna litz wire is made of 1.0 mm2 fine stranded copper conductor with a black PVC insulation. The total diameter is about 2 mm. Ideal for experiments or vacation antennas. Since the core is only copper, this stranded wire will always elongate a bit over time, making it thinner. The tensile strength of this antenna strand is limited. Copper/Kevlar antenna litz wire This antenna litz wire is manufactured specifically for antennas. The litz consists of a Kevlar core with approx. 1.1 mm2 tinned and fine stranded copper conductors. 1x 0.4 mm Kevlar and 24x 0.25 mm copper. The jacket is made of black UV-resistant PE. The total diameter is approx. 2.5 mm. The tensile strength is approx. 50 kg. You will receive a strong, flexible and relatively light antenna litz wire. These complete Mini End Fed Multiband kits are designed for 100 Watt PEP Phone and are available in these configurations: 10-20-40 meters approximately 20 meters in length, without extension coil.10-20-40 meters, approx. 12 meters length, with 34uH extension coil10-15-20-40-80 meters, approximately 21 meters in length with 110uH extension coil. This kit contains: 23 meters of antenna wire19 mm PVC pipe with approx: 110uh coil1x stainless steel cable clamp1x end insulator1x cable lug 5mm1x heat shrink tubing 1:49 Mini impedance transformer:IP65 housing 64x58x35mm polycarbonateFerrite toroid Amidon FT140-43Winding wire 1,00 mm100 pF capacitor 1kV1x BNC flange socket2x M2,5 screws 8/10mm2x M2,5 nut2x M2,5 washer1x cable lug 3mm3x M5 cable lug2x stainless steel M5 screw 20mm2x stainless steel M5 wing nut2x stainless steel M5 collar nut2x stainless steel M5 lock washer2x stainless steel M5 screw 20mm2x stainless steel M5 wing nut2x stainless steel M5 collar nut2x stainless steel M5 tooth lock washer1x ring M41x tooth lock washer M41x nut M41x cable thimble You can find the building instructions here: TO THE CONSTRUCTION INSTRUCTION ** The construction manual is just getting its fine tuning

3x snaphooks A4Thanks to their rust resistance (material 316), these stainless steel snaphooks can be used permanently outdoors or in the wet. They have a length of 50 millimeters, with the snap hook measuring five millimeters in diameter. The total weight that this snap hook can support is 95dan, about 85 kilograms. This should be enough for tie-off. Technical data snap hook Length: 50 mmWidth: 25 mmInner length: 40 mmThickness: 5 mmInner width: 15 mmOpening: 7 mminner width eyelet: 8 mmmax. weight load 85 kgmin. breaking load 200 kg