Multi Isolator Maxi 120x16x16mm

End Fed multiband antenna DIY kit for 10-15-20-40-80m 300Watt PEP SSBNew extended kit! This kit contains all the necessary components to build an EndFed 1:49 multiband antenna for the bands 10-15-20-40-80 meters up to 300 Watt PEP Phone. We have added a connection for the counterweight and the useful stainless steel ring etc. to the kit. This End Fed kit is supplied with the antenna wire of your choice: Standard antenna wire: This antenna wire consists of 1.0 mm2 fine stranded copper conductor with black PVC insulation. The total diameter is approx. 2 mm. Ideal for experiments or vacation antennas. As the core is only made of copper, this stranded wire will become slightly longer and therefore thinner over time. The tensile strength of this stranded antenna wire is limited. LF Antenna Strand - New!This high-quality antenna strand consists of 32 individual 0.20 mm wires made of hard-drawn, bare copper. The conductor cross-section is approximately 1.0 mm² and offers excellent conductivity combined with high mechanical strength. It has a total diameter of 2.1 mm, a weight of approx. 11 g/m, and a breaking load of about 40 kg. The robust black polyethylene (PE) insulation reliably protects the strand from environmental influences and ensures a long service life. The kit contains the following components: 1x toroidal core FT-240-431x enameled copper wire GR2 for winding the toroidal core (1mm) approx. 1.50 meters1x polycarbonate housing with transparent cover 100x100x60 mm (IP67)1x mini insulator 65 * 15mm2x simplex terminals up to 2 mm wire (wire rope terminal) 1x thimble approx. 23.5 meter antenna wire 1mm² black 1x capacitor 100pF 2kV DC 1x PL259 panel jack 1x extension coil 110uH ready wound and measured 1x shrink tube black 25.4-12.7mm 1x various screws, washers and nuts made of stainless steel 1x stainless steel ring 3x Fast-On ring contactType: MultibandLength: approx. 23 meters Connection: PL Max. Power: 300Watt PEP Phone Weight: approx. 600g Balun 1:49Informationen gemäß Art. 19 GPSR Adresse des Herstellers: Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.netAdresse der verantwortlichen Person: Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net

End Fed multiband antenna DIY kit for 10-20-40m 300Watt PEP SSBNew extended kit! This kit contains all the necessary components to build an EndFed 1:49 multiband antenna for the bands 10-20-40meters up to 300 Watt PEP Phone. We have added a connection for the counterweight and the useful stainless steel ring etc. to the kit. This End Fed kit is supplied with the antenna wire of your choice: Standard antenna wire: This antenna wire consists of 1.0 mm2 fine stranded copper conductor with black PVC insulation. The total diameter is approx. 2 mm. Ideal for experiments or vacation antennas. As the core is only made of copper, this stranded wire will become slightly longer and therefore thinner over time. The tensile strength of this stranded antenna wire is limited. LF Antenna Strand - New!This high-quality antenna strand consists of 32 individual 0.20 mm wires made of hard-drawn, bare copper. The conductor cross-section is approximately 1.0 mm² and offers excellent conductivity combined with high mechanical strength. It has a total diameter of 2.1 mm, a weight of approx. 11 g/m, and a breaking load of about 40 kg. The robust black polyethylene (PE) insulation reliably protects the strand from environmental influences and ensures a long service life. The kit contains the following components: 1x toroidal core FT-240-431x enameled copper wire GR2 for winding the toroidal core (1mm) approx. 1.50 meters1x polycarbonate housing with transparent cover 100x100x60 mm (IP67)1x mini insulator 65 * 15mm2x simplex terminals up to 2 mm wire (wire rope terminal) 1x thimble approx. 23.5 meter antenna wire 1mm² black 1x capacitor 100pF 2kV DC 1x PL259 panel jack 1x extension coil 34uH ready wound and measured 1x shrink tube black 25.4-12.7mm 1x various screws, washers and nuts made of stainless steel 1x stainless steel ring 3x Fast-On ring contactType: MultibandLength: approx. 12 meters Connection: PL Max. Power: 300Watt PEP Phone Weight: approx. 600g Balun 1:49 Informationen gemäß Art. 19 GPSR Adresse des Herstellers:  Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net Adresse der verantwortlichen Person: Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net

New extended kit! This kit contains all the necessary components to build an EndFed 1:649 multiband antenna for the bands 10-12-15-17-20-(30*)-40-80-160 up to 300 Watt PEP Phone. We have added a connection for the counterweight and the useful stainless steel ring etc. to the kit. This End Fed kit is supplied with the antenna wire of your choice: Standard antenna wire: This antenna wire consists of 1.0 mm2 fine stranded copper conductor with black PVC insulation. The total diameter is approx. 2 mm. Ideal for experiments or vacation antennas. As the core is only made of copper, this stranded wire will become slightly longer and therefore thinner over time. The tensile strength of this stranded antenna wire is limited. LF Antenna Strand - New!This high-quality antenna strand consists of 32 individual 0.20 mm wires made of hard-drawn, bare copper. The conductor cross-section is approximately 1.0 mm² and offers excellent conductivity combined with high mechanical strength. It has a total diameter of 2.1 mm, a weight of approx. 11 g/m, and a breaking load of about 40 kg. The robust black polyethylene (PE) insulation reliably protects the strand from environmental influences and ensures a long service life. The kit contains the following components: 1x toroidal core FT-240-431x enameled copper wire GR2 for winding the toroidal core (1mm) approx. 1.80 meters1x polycarbonate housing with transparent cover 100x100x60 mm (IP67)1x mini insulator 65 * 15mm2x simplex terminals up to 2 mm wire (wire rope terminal) 1x thimble approx. 23.5 meter antenna wire 1mm² black 1x capacitor 100pF 2kV DC 1x PL259 panel jack 1x extension coil 34uH ready wound and measured 1x shrink tube black 25.4-12.7mm 1x various screws, washers and nuts made of stainless steel 1x stainless steel ring 3x Fast-On ring contactType: Multiband 1:64 Length: approx. 46 meters Connection: PL Max. Power: 300/600Watts PEP Phone Weight: ca 600g Info The measurements for this antenna were made on two 12m spider beam masts, 10 meters above the ground, in an open field, without any buildings. Informationen gemäß Art. 19 GPSR Adresse des Herstellers:  Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net Adresse der verantwortlichen Person: Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net

Pressure compensating valve for Endfed kits. Easy to install in an 8 mm hole. This pressure compensating valve ensures stable performance in all weather conditions. Air pressure differences in the outside air can cause moisture to enter the enclosure through ports and bushings. Ports and bushings. The air pressure compensating valve contains a membrane that compensates for air pressure differences. Waterproof, protection class IP66 / IP68 For use in BalUn and UnUn enclosures To be placed in 8mm hole.

End Fed multiband antenna DIY kit for 10-15-20-40-80m 100Watt PEP SSBNew extended kit! This kit contains all the necessary components to build an EndFed 1:49 multiband antenna for the bands 10-15-20-40-80 meters up to 100 Watt PEP Phone. We have added a connection for the counterweight and the useful stainless steel ring etc. to the kit. This End Fed kit is supplied with the antenna wire of your choice: Standard antenna wire: This antenna wire consists of 1.0 mm2 fine stranded copper conductor with black PVC insulation. The total diameter is approx. 2 mm. Ideal for experiments or vacation antennas. As the core is only made of copper, this stranded wire will become slightly longer and therefore thinner over time. The tensile strength of this stranded antenna wire is limited. LF Antenna Strand - New!: This high-quality antenna strand consists of 32 individual 0.20 mm wires made of hard-drawn, bare copper. The conductor cross-section is approximately 1.0 mm² and offers excellent conductivity combined with high mechanical strength. It has a total diameter of 2.1 mm, a weight of approx. 11 g/m, and a breaking load of about 40 kg. The robust black polyethylene (PE) insulation reliably protects the strand from environmental influences and ensures a long service life. The kit contains the following components: 1x toroidal core FT-140-431x enameled copper wire GR2 for winding the toroidal core (1mm) approx. 1.00 meter1x polycarbonate housing with transparent cover 100x100x60 mm (IP67)1x mini insulator 65 * 15mm2x simplex terminals up to 2 mm wire (wire rope terminal) 1x thimble approx. 23.5 meter antenna wire 1mm² black 1x capacitor 100pF 2kV DC 1x PL259 panel jack 1x extension coil 110uH ready wound and measured 1x shrink tube black 25.4-12.7mm 1x various screws, washers and nuts made of stainless steel 1x stainless steel ring 3x Fast-On ring contactType: MultibandLength: approx. 23 meters Connection: PL Max. Power: 100Watt PEP Phone Weight: approx. 500g Balun 1:49 Informationen gemäß Art. 19 GPSR Adresse des Herstellers:  Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net Adresse der verantwortlichen Person: Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net

End Fed multiband antenna DIY kit for 10-20-40m 100Watt PEP SSBNew extended kit! This kit contains all the necessary components to build an EndFed 1:49 multiband antenna for the bands 10-20-40meters up to 100 Watt PEP Phone. We have added a connection for the counterweight and the useful stainless steel ring etc. to the kit. This End Fed kit is supplied with the antenna wire of your choice: Standard antenna wire: This antenna wire consists of 1.0 mm2 fine stranded copper conductor with black PVC insulation. The total diameter is approx. 2 mm. Ideal for experiments or vacation antennas. As the core is only made of copper, this stranded wire will become slightly longer and therefore thinner over time. The tensile strength of this stranded antenna wire is limited.  LF Antenna Strand - New! This high-quality antenna strand consists of 32 individual 0.20 mm wires made of hard-drawn, bare copper. The conductor cross-section is approximately 1.0 mm² and offers excellent conductivity combined with high mechanical strength. It has a total diameter of 2.1 mm, a weight of approx. 11 g/m, and a breaking load of about 40 kg. The robust black polyethylene (PE) insulation reliably protects the strand from environmental influences and ensures a long service life. The kit contains the following components: 1x toroidal core FT-140-431x enameled copper wire GR2 for winding the toroidal core (1mm) approx. 1.0 meters1x polycarbonate housing with transparent cover 100x100x60 mm (IP67)1x mini insulator 65 * 15mm2x simplex terminals up to 2 mm wire (wire rope terminal) 1x thimble approx. 23.5 meter antenna wire 1mm² black 1x capacitor 100pF 2kV DC 1x PL259 panel jack 1x extension coil 34uH ready wound and measured 1x shrink tube black 25.4-12.7mm 1x various screws, washers and nuts made of stainless steel 1x stainless steel ring 3x Fast-On ring contactType: MultibandLength: approx. 12 meters Connection: PL Max. Power: 100Watt PEP Phone Weight: approx. 550g Balun 1:49 Informationen gemäß Art. 19 GPSR Adresse des Herstellers:  Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net Adresse der verantwortlichen Person: Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net