RG58 CU MIL-C-17G Koaxialkabel made in Italy by SIVA Cavi Dieses RG58 CU ist ein flexibles und preiswertes Koaxialkabel aus dem Hause SIVA. Es kommt aus Italien und entspricht dem höchsten UL-Standard MIL C 17 "G". Das Kabel besitzt eine Kupferlitze verzinnt als Innenleiter. Der Außenleiter aus verzinntem Kupfergeflecht, mit 112x0,13mm Drähten, einer Abdeckung von 94% und einer Schirmung von >57dB.  Aufbau Innenleiter 19 x 0,18 mm CU SN CU SN = Kupfer verzinnt Isolation 2,95 mm PE ± 0,1 Außenleiter Cu-Geflecht verzinnt, mit 112 x 0,13mm Drähten und 95%Abdeckung Mantel 5mm PVC2 schwarz ± 0,2 Bruchlast 139 N Biegeradius min. 25 mm Kupferzahl 18,7 kg/km Temperaturbereich -30°C bis +70°C Elektrische Daten Impedanz 50 Ohm ± 3 Kapazität 100 pF/m Verkürzungsfaktor 0,66 Schleifenwiderstand 53 Ohm/km Schrimung; bis 900MHz >57dB Wichtig! Wir können von diesem RG50 CU Kabel maximal 100 Meter am Stück liefern, da wir ausschließlich 100m Rollen am Lager haben.

SIVA RF 400 UF-PVC low loss Koaxialkabel 10,3 mm Das RF400 UF ist eine sehr gute Alternative in der 10,3mm Koaxialkabelklasse und für den Frequenzbereich bis 3 GHz geeignet. Dieses doppelt geschirmte Koaxkabel, hat eine geringe Dämpfung und gute Flexibilität. Der Innenleiter wird aus 7x1mm Drähten gefertigt. Das Geflecht, umschließt die kunststoffbeschichtete Kupferfolie, mit einem Bedeckungsgrad von 78%.  Die gravierenden Unterscheide zu einem RG58U, haben wir in einem Artikel ausführlich, mit vielen realen Beispielen beschrieben: zum Artikel Eigenschaften Sehr flexibel Für Rotorbetrieb geeignet Innenleiter mit 7 Drähten (7x1mm) Für Frequenzen bis 3 GHz geeignet UV-beständig Es können viele RG-213 übliche Antennenstecker genutzt werden. Schirmung: > 80dB (100-900 MHz)> 70dB (900-2000 MHz)> 60dB (2000-3000 MHz) Kabelaufbau: Innenleiter: Kupfer, 7x1,0 mm, Ø 2,9 mm ± 0,05Dielektrikum: PE geschäumt, PEG Ø 7,3 mmAußenleiter 1: Kupferfolie, kunststoff beschichtetAußenleiter 2: Kupfergeflecht, opt. Bedeckung 73%, 112 Drähte Außenhaut: PVC, hoch flexibel, Ø 10,2 mm ± 0,15 mm UV-resistent Kabelgewicht: Kilogram per Kilometer: Kupfer: 81.0 kg / km Kunststoff: 63.8 kg / km Gesammt: 144.8 kg / km Dämpfung bei 20°C (dB x 100 meters) 5 MHz - 1.1dB10 MHz - 1.5dB50 MHz - 2.9dB200 MHz - 6.0dB500 MHz -10.3dB800 MHz - 13.2dB1000 MHz - 15.0dB3000 MHz - 28.1dB Komplettes Datenblatt: Download

Messi&Paoloni Ultraflex 10 - Abverkauf zum Sonderpreis Wir haben eine Rolle Ultraflex 10, original von Messi&Paoloni, mit 200m am Lager. Da wir das Kabel sonst nicht führen, bieten wir Ihnen dieses Kabel zum Sonderpreis im Abverkauf an.  Ultraflex 10 von Messi&Paoloni ist ein flexibles, low-loss Koaxialkabel für den Einsatz bis zu 8 GHz.Die geringe Dämpfung des Ultraflex 10 wird durch die Verwendung eines verlustarmen, dreischichtigen Zell PE PEGPE-Dielektrikums ermöglicht.Der Innenleiter von Ultraflex 10 besteht aus flexibler Kupfer-Litze (7x1mm) und der Außenleiter besteht aus 100%-überlappender Kupferfolie sowie einem Kupfergeflecht aus 144 Drähten. Die Kupferfolie ist auf der Innenseite PE-beschichtet.Die Außenisolierung von Ultraflex 10 besteht aus elastischem UV-stabilisiertem PVC. ATTENUATION (20°C /68°F)FREQUENCY dB/100m1,8 MHz 0,83,5 MHz 1,07 MHz 1,210 MHz 1,314 MHz 1,521 MHz 1,828 MHz 2,050 MHz 2,7100 MHz 3,9144 MHz 4,7200 MHz 5,7400 MHz 8,3430 MHz 8,6800 MHz 12,11000 MHz 13,81296 MHz 16,42400 MHz 23,73000 MHz 27,34000 MHz 32,95000 MHz 38,96000 MHz 44,57000 MHz 50,28000 MHz 55,8

PL-connector UHF-Special 10 This high-quality PL-259 connector is suitable for the coax cable types:  HyperFlex 10, H 2010, H 2010 FRNC = Calorix 10, Ecoflex 10, Ultraflex 10,H2000 Flex, H 1000, LMR 400, MMR 400, Neoflex 10.  Type: UHF connector special Design: Connector Connection: Soldering Cable inlet Ø10,3 mm Material: Housing: nickel-plated brass. Dielectric: PTFE We use these connectors for the prefabricated Hyperflex 10 coax cables. The assembly instructions can be downloaded here or under the "Media" tab.

The Messi & Paoloni MP-CO.UHF.7M-S-EVO is a UHF Male (PL259) solder enhanced connector for 7.3mm / .287" cables. Genuine Messi & Paoloni enhanced solder connector UHF Male (PL259) 2-Pack Compression design with double seal to ensure better protection against infiltration of water, humidity and condensation Easy installation and welding instructions included in the package (no braid soldering needed) Dramatic suppression of the background noise, improvement of screening attenuation and insertion losses The UHF Evolution can be used up to 6000 MHz, a well made PL259 is barely acceptable up to 2000 MHz Model MP-CO.UHF.7M-S-EVO Product dimensions: 0.82 x 1.81 in. (2.1cm x 4.6cm) Wrench size: 0.63 in (16mm) For ULTRAFLEX 7 /.287'' cable Note: The new designed pin prevents excess of tin and the consequent heating, which damages the dielectric causing an uncontrollable alteration of the electrical properties of your cable.

Over Voltage Protector OVP1000 Small part, big impact!Triple protection against overvoltages on the antenna line: To protect your receiver we offer the OVP1000 a new surge (Over Voltage Protector). Built-in coaxial lines, so be high current pulses as generated by lightning strikes in the immediate vicinity derived. These protect the OVP 1000 on three counts against overvoltages on the antenna line: Antenna side: A gas discharge tube with 60V ignition voltage, max. Pulse discharge current 1 kA (8 / 20us) On the receiver side. An ultrafast diode ESD (30KV max pulse power 350W (8 / 20us) Input and output are also for DC voltages up to max. Blocked 100V Without replaceable cartridge, the system is completely replaced. Not waterproof. Extremely broadband deployment Frequency range: 200Hz - 1GHz (type 1 dB insertion loss.)RCA sockets: BNC Made in Germany Overvoltage protection OVP1000 in practical use I inserted the 1000 inline while listening to Old Time Radio on 6770 AM, on my beverage. Not only did it decrease clipping without attenuator inline, it eliminates the DC clips with attenuator engaged!!! I can say from experience, the OVP1000 is reasonably priced, protection device that offers no noticeable insertion loss of signal & obviously drops the induced static… Read the Article in the Bonito Newsroom    Please read carefully and Disclaimer:The OVP 1000 is no protection of the antenna line against direct lightning strike, since lightning always seeking kürzsten way to Earth, which does not necessarily take place via the coaxial cable. Therefore, the protection function is limited to overvoltages and potential differences between Koaxmasse (shield and inner conductor). Therefore, a liability for connected devices is generally excluded! When not in use, absence, broadcasting or lightning storms in the receiver should be disconnected to prevent damage from the antenna line! Made in Germany

LP060 Low Pass Filter The elliptically-formed low pass filter LP060 from NTi suppresses all frequencies above 60 MHz. Highly effective antennas combined with near-by strong FM stations often overburden the input of the radio and cause interference and phantom signals. The LP060 was developed aiming at the highest possible suppression in the 88MHz - 108 MHz FM band, whereas as the 6m amateur radio band at 50MHz is still totally within the pass band. For the greatest possible effectiveness, the low pass filter  should be inserted directly before the receiver input.  Attenuation values (typ.):52MHz: -1dB60MHz: -3dB80 MHz: -55dB88-110 MHz: -90dB110-150MHz: -75dB150-200MHz: -70dB200-400MHz: -65 dB Dimension: 88mm x 31mm x 25mm (3,46 x 1,22 x 0,98 inch) Input and output are DC-blocked (max. 50V DC) Attention: Only suitable for reception, high HF (>10dbm) will cause permanent damage! Successfully tested with: Elad FDM-S1 and FDM-S2, FiFi-SDR1.0 and 2.0, PM-SDR, Winradio Excalibur, RFSpace SDR-IQ Made in Germany

PL-Connector UHF-Special 13 13mm UHF-connector for Ultraflex 13 and Hyperflex 13 by Messi&Paoloni Manufacturer's number: UHF-Spezial 13

7/16 HF-connector for 10-11mm Coax cable This high quality 7/16 RF connector is for the coax cable types: HyperFlex 10, H 2010, H 2010 FRNC = Calorix 10, Ecoflex 10, Ultraflex 10,H2000 Flex, H 1000, LMR 400, MMR 400, Neoflex 10 u.ä. It is made of TA (Tres Alloy CuSnZn3) white bronze and of course with PTFE dielectric.  

HP0020 High Pass Filter The elliptically-formed high pass filter HP0020 suppresses all frequencies below 2 MHz.  Strong or near-by transmitters in the long- or medium wave range can cause interferences and intermodulation in the shortwave range, which can effectively be suppressed with this filter.  The HP0020 filter is very steep, so that signals in the upper medium wave range are already suppressed effectively. For the greatest possible effectiveness, the low pass filter  should be inserted directly before the receiver input.  Attenuation values (typ.):<0.50 MHz:-55dB1.0MHz: -45dB1.6 MHz:-35dB2.0MHz: -3dB>2.5 MHz: -1dB Input and output are DC-blocked (max. 50V DC) Dimensons: 88mmx31mmx25mm (3,46 x 1,22 x 0,98 inch) Attention: Only suitable for reception, high HF (>10dbm) will cause permanent damage! Because the filter is DC-blocked, it has to be inserted between the receiver input and the power inserter. Successfully tested with: Elad FDM-S1 and FDM-S2, FiFi-SDR1.0 and 2.0, PM-SDR, Winradio Excalibur, RFSpace SDR-IQ

Preamplifier/Vorverstärker 144MHz EME-Contest-DX-SATEin 144 MHz (2 Meter) UKW-Vorverstärker mit innovativem Design. Kerbfilter 88-108MHz. Verwendet wurde ein ATF531P8-Modul mit einer Rauschzahl von nur 0,30db. Perfekt für den Einsatz: Sat, EME, Contest und DX. Aus Anticorodal Aluminium im zylindrischen Design. 9-13.8 Volt bei 100mA Impedence:50Ohm Verstärkung:+23dB OIP3 : +29dBm N-Stecker / N-Buchse

The Messi & Paoloni MP-CO.UHF.7M-S-EVO is a UHF Male (PL259) solder enhanced connector for 7.3mm / .287" cables. Genuine Messi & Paoloni enhanced solder connector UHF Male (PL259) 2-Pack Compression design with double seal to ensure better protection against infiltration of water, humidity and condensation Easy installation and welding instructions included in the package (no braid soldering needed) Dramatic suppression of the background noise, improvement of screening attenuation and insertion losses The UHF Evolution can be used up to 6000 MHz, a well made PL259 is barely acceptable up to 2000 MHz Model MP-CO.UHF.7M-S-EVO Product dimensions: 0.82 x 1.81 in. (2.1cm x 4.6cm) Wrench size: 0.63 in (16mm) For ULTRAFLEX 7 /.287'' cable Note: The new designed pin prevents excess of tin and the consequent heating, which damages the dielectric causing an uncontrollable alteration of the electrical properties of your cable.

CCMC50 Common Mode Noise Filter   Noise filters are nothing new and are often used for transmitting purposes. They are used to prevent unwanted radiation via the coax shielding. It is less known that they can also suppress unwanted radiation when receiving signals, especially when an active antenna is used. However, in this case, the situation is reversed: en route to the antenna, unwanted interferences from electric home appliances can be effectively eliminated.   This Coaxial Common Mode Choke (CCMC50) has been especially optimized for maximum common mode noise rejection of >30dB wide band in the frequency range of 500kHz – 50MHz. With slight limitations a much wider frequency range is covered. This is possible by using a cascaded system of ferrite cores with various frequency dependent material properties, combined with high quality PTFE coaxial cable. We recommend to connect the CCMC50 as closely as possible to the receiver.   For the highest demands we still offer the proven Common Mode Noise Filter CCMC30, which is specially optimized for maximum Common mode noise rejection of guaranteed> 30dB broadband in the reception range from 150kHz - 30MHz.   With the CCMC50 a reasonably priced version is now available with the following minor limitations against the CCMC30:   Common mode noise rejection guaranteed> 30dB, broadband in the reception range from 500kHz - 50MHz instead of starting at 150kHz. Starting with the medium wave over short wave up to the 6m amateur radio band, which should be sufficient for most applications. Not suitable for outdoor use because it is not splashproof.   With regard to efficient noise suppression, the CCMC50 is not very much different from the galvanic isolator GI1000. However, the CCMC50 performes down to lowest frequencies including DC voltage, in contrast to the GI1000, which blocks DC voltages and very low frequencies. The CCMC50 can thus be connected directly to the coax cable which passes the supply voltage or the control signals to the active antenna. A series connection of the GI1000 directly connected to the receiver followed by the CCMC50 right behind the power inserter may result in an even better performance. Technical Data Optimal frequency range: 500 kHz – 50 MHz Common Mode Wave suppression: >30 dB: 500 kHz -50MHz (>20 dB: 100kHz-70MHz) Insertion loss: <1 dB max. 500MHz, < 1.5dB bis max 1.5GHz Size: 127x65x43mm (160mm with BNC connectors) Connectors: 2x BNC 50Ohm Weight: 160g Made in Germany Absolutely not for transmitting purposes!

Preamplifier/Vorverstärker 144MHz VOX bis 100Watt Der 144 MHz (2 Meter) UKW-Vorverstärker mit neuem und innovativem Design. Diese VOX-Version ist bis 100Watt Sendeleistung belastbar und arbeitet mit einer Rauschzahl von nur 0,50db wenn das Relais geschaltet ist. Verwendet wurde ein GaAs ATF531P8-Modul mit einer Rauschzahl von nur 0,50db (bei geschaltetem Relais) und einem Kerbfilter 88-108MHz für das bestmöglich Resultat. Das anliegende Signal des 2 Meterbandes wird um +23dB verstärkt. Perfekt für den Einsatz: Sat, EME, Contest und DX. Aus Anticorodal Aluminium im zylindrischen Design. 9-13.8 Volt bei 120mA Impedence:50Ohm Verstärkung:+23dB OIP3 : +29dBm N-Stecker / N-Buchse Max power IN : 500mW bis 100W

Our 50 Ohm soldering BNC socket with sealing ring, PTFE dielectric, gold-plated center pin. Available for cables with 7mm like Ultraflex 7, Highflexx 7, Aircell 7 etc. Our BNC cable socket is suitable for all cables of the 7mm dimension. This BNC socket is provided with 1 ground connection sleeves and 1 center pins. The center contacts are diamagnetic.

Dieser hochwertige TNC-Stecker ist für 10mm Koaxkabel geeignet, besitzt eine nickelfreie Oberfläche (TresAlloy), sowie einen Silikon-O-Ring, der die Wasserdichtigkeit erhöht. Die begefügten Mittelstifte sind paramagnetisch.

BNC-connector (plug) for 7 mm coax cables This BNC connector is suitable for soldering to Ultraflex 7, HIGHFLEXX 7, Aircell 7 cable. It has a nikel-plated plug housing, PTFE dielectric and a gold-plated center contact. Also included is a piece of scraping tubing.

Unfortunately we cannot be on air every day! So that your radios, power amplifiers, loudspeakers etc. do not get dusty, there are now beautiful and practical dust covers from DX Covers. The DX Covers dust covers are made of soft and high quality leatherette and specifically tailored to fit the different devices. They also offer a light level of mechanical protection from small items coming into contact with your equipment.It leaves enough space for the connectors and cables. The high quality leatherette used is smooth, soft and easy to care for. Soft felt is also sewn into the inside to protect the sensitive displays. The back is open, so there is enough space for antenna cables, accessory connections or control cables. Premium quality that immediately catches the eye Each DX Cover dust cover is lovingly made in England from high quality leatherette and then embroidered with the company logo and the model number. Once this is completed, the cover is then lined in a soft felt which helps to keep your equipment looking as good as the day it came out of the factory. The DX covers fit perfectly on your device. You will notice the fantastic quality and loving workmanship as soon as you unpack. DX Covers dust covers are approved to use the manufacturer logos of: Acom, Ameritron, Elad, Elecraft, Expert Electronics, Icom, Kenwood, MFJ, OM Power, Palstar, RF-KIT, SPE and Yaesu.

Unfortunately we cannot be on air every day!So that your radios, power amplifiers, loudspeakers etc. do not get dusty, there are now beautiful and practical dust covers from DX Covers. The DX Covers dust covers are made of soft and high quality leatherette and specifically tailored to fit the different devices. They also offer a light level of mechanical protection from small items coming into contact with your equipment.It leaves enough space for the connectors and cables. The high quality leatherette used is smooth, soft and easy to care for. Soft felt is also sewn into the inside to protect the sensitive displays. The back is open, so there is enough space for antenna cables, accessory connections or control cables. Premium quality that immediately catches the eyeEach DX Cover dust cover is lovingly made in England from high quality leatherette and then embroidered with the company logo and the model number. Once this is completed, the cover is then lined in a soft felt which helps to keep your equipment looking as good as the day it came out of the factory. The DX covers fit perfectly on your device. You will notice the fantastic quality and loving workmanship as soon as you unpack. DX Covers dust covers are approved to use the manufacturer logos of: Acom, Ameritron, Elad, Elecraft, Expert Electronics, Icom, Kenwood, MFJ, OM Power, Palstar, RF-KIT, SPE and Yaesu.