Mini Endfed Antenna Kit for 10-15-20-40-80m

€49.50*

% €55.00* (10% saved)

Content: 1 Stück

No longer available

Antenna wire

Cooper /Kevlar Litz wire

Standard litz wire

Product number: 0657

Product information "Mini Endfed Antenna Kit for 10-15-20-40-80m"

Mini Endfed Antenna Kit for 10-15-20-40-80m, max 100 Watts PEP and 1:49 Transformer

The Mini Endfed is a small endfed antenna solution for mobile use, travel, QRP, SOTA (Summit on the Air) or DX expeditions etc. The IP65 protected polar carbonate housing with a size of only 64x58x35 mm, can be easily stored in your pocket or backpack. The weight is about 250-500 grams, depending on the length of the spotlight.

The kit has both a connector for the ANTenna and GND for a counter poise capacitance. We have also integrated the M4 ring. This makes it very easy to attach the Mini Endfed with a carabiner and use the thimble as a strain relief. All screws, nuts and the ring are made of stainless steel.

If you attach the antenna to the top of a telescopic mast and slide out the mast segments, you are on the air within minutes! To attach the body of the 1:49 Transformer to a mast, you can use the same bracket as used by our active antennas.

This End Fed Multiband Antenna comes with the antenna wire of your choice:

Standard Antenna wire:

This antenna litz wire is made of 1.0 mm2 fine stranded copper conductor with a black PVC insulation. The total diameter is about 2 mm. Ideal for experiments or vacation antennas. Since the core is only copper, this stranded wire will always elongate a bit over time, making it thinner. The tensile strength of this antenna strand is limited.

Copper/Kevlar antenna litz wire

This antenna litz wire is manufactured specifically for antennas. The litz consists of a Kevlar core with approx. 1.1 mm2 tinned and fine stranded copper conductors. 1x 0.4 mm Kevlar and 24x 0.25 mm copper. The jacket is made of black UV-resistant PE. The total diameter is approx. 2.5 mm. The tensile strength is approx. 50 kg. You will receive a strong, flexible and relatively light antenna litz wire.

These complete Mini End Fed Multiband kits are designed for 100 Watt PEP Phone and are available in these configurations:

10-20-40 meters approximately 20 meters in length, without extension coil.
10-20-40 meters, approx. 12 meters length, with 34uH extension coil
10-15-20-40-80 meters, approximately 21 meters in length with 110uH extension coil.

This kit contains:

23 meters of antenna wire
19 mm PVC pipe with approx: 110uh coil
1x stainless steel cable clamp
1x end insulator
1x cable lug 5mm
1x heat shrink tubing

1:49 Mini impedance transformer:
IP65 housing 64x58x35mm polycarbonate
Ferrite toroid Amidon FT140-43
Winding wire 1,00 mm
100 pF capacitor 1kV
1x BNC flange socket
2x M2,5 screws 8/10mm
2x M2,5 nut
2x M2,5 washer
1x cable lug 3mm
3x M5 cable lug
2x stainless steel M5 screw 20mm
2x stainless steel M5 wing nut
2x stainless steel M5 collar nut
2x stainless steel M5 lock washer
2x stainless steel M5 screw 20mm
2x stainless steel M5 wing nut
2x stainless steel M5 collar nut
2x stainless steel M5 tooth lock washer
1x ring M4
1x tooth lock washer M4
1x nut M4
1x cable thimble

You can find the building instructions here: TO THE CONSTRUCTION INSTRUCTION ** The construction manual is just getting its fine tuning

Accessory Items

BNC flange connector

BNC flange connector BNC flange connector with PTFE dielectric and gold plated center contact. This connector is also used for our Mini-Endfed kits. Hole diameter 3mm

€2.95*

2-Loch UHF / PL Flanschbuchse SO-239

2-Loch UHF / PL Flanschbuchse SO-239 mit PTFE-Isolierung und vergoldetem Mittelkontakt.

€2.55*

Antenna mast mounting bracket for Boni-Whip, MegActiv, GigActiv and Megaloop

This V4A mounting bracket fits for the Boni-Whip, MegActiv, GigActiv and the MegaLoop.

From €17.99*

Details

Gehäuse für Endfed Antennen aus Polycarbonat

Enclosure for Endfed Antennas Polycarbonate

Enclosure for Endfed Antennas Polycarbonate Now with transparent lid! Single enclosure of our EndFed antenna kits, with transparent lid, as a spare part or just for experimenting. The enclosre is made of polycarbonate, as in the kit. Polycarbonate housings are more weather-resistant and UV-resistant than ABS housings. Dimensions: 100 x 100 x 55mmColour: light greyMaterial: polycarbonateProtection class: IP 65Screws and gasket included

€12.00*

Hamrope PES 4

Hamrope PES 4 Our best selling universal guy line for the radio amateur. For portable and stationary use. The quality polyester has excellent UV resistance and is suitable for long-term use. The elasticity of this braided rope has a shock absorbing effect and is desirable and often necessary for the use of radio amateurs. The attractive design allows the product to fit well into a natural environment, yet be perceived sufficiently. Hamrope PES 4 Polyester, 4mm diameter tensile strength approx. 260 daN(~Kg) Colour: olive green with red marker Length: 50 meter

€17.50*

Enclosure for mini Endfed Antennas Polycarbonate

Enclosure for mini Endfed Antennas Polycarbonate Single enclosure of our mini EndFed antenna kits as a spare part or just for experimenting. The enclosre is made of polycarbonate, as in the kit. Polycarbonate housings are more weather-resistant and UV-resistant than ABS housings. Dimensions: 64x58x35mmColour: light greyMaterial: polycarbonateProtection class: IP 65Screws and gasket included

€7.90*

Mini insulator for wire antennas

Mini insulator for wire antennas Our mini insulators from our Endfed kits are now also available seperately. The Mini Isolator can be used multifunctionally, for example as strain relief for dipoles and EndFed antennas. Furthermore it is also suitable as a holder for Endfed antennas or balun housings. Features Color: ClearMaterial: Plastic UV resistantDimensions: 65 x 15 x 8 mm

€2.00*

Koaxkabel mit integriertem RFI-Choke (Mantelwellensperre)

Coax cable with integrated RFI choke

This pre-assembled coaxial cable with integrated RFI choke for End Fed antennas is ready for immediate use. Thanks to its design based on the W2DU principle, the common mode choke is extremely broadband and low-loss. It effectively prevents the shielding of the coaxial cable from becoming part of the antenna system and radiating unintentionally. It therefore provides effective protection against unwanted RF interference. It also serves to adapt the unbalanced coaxial cable to balanced antennas and can therefore also be used as a “1:1” balun. A variety of highly permeable ferrites are threaded onto lightweight HF-195 FX-ZH low-loss coaxial cable, shrink-wrapped and assembled with connectors as required. The integrated RFI choke (common mode choke) is installed at the end of the cable after 2.10m for the 10-40m bands or after 4.20m for the 10-80m bands. We offer lengths of 10, 15 and 20m. Other lengths can be produced on request. The lightweight coaxial cable with integrated RFI choke (common mode choke) is also ideal for portable use when traveling, QRP, COTA, POTA, IOTA, SOTA (Summit on the Air) or DX expeditions. 50 Ohm HF195 FX-ZH coaxial cableReady for immediate usefor 10-40m or 10-80m bandPlug and PlayChoice of cable lengthConnector of your choicePower limit Max: 250W PEP SSB Translated with DeepL.com (free version)

From €59.00*

Details

2-Loch N Flanschbuchse

2-Loch N Flanschbuchse Mit PTFE-Isolierung (hoch temperaturbeständig) und vergoldetem Mittelkontakt.

€4.49*

Tip

Spiderbeam 7m or 10m Mini fiberglass pole

Mini telescopic pole with only 71cm transport length, fits in any suitcase. This pole is easy to carry and ready installed within a minute. Although it is light and small enough to fit in any large suitcase, it was developed to be rugged and durable! This ultra-portable Mini pole has a heavy-duty screw-on base cap at the bottom to protect its segments from rocks and mud. Nubs on the bottom of the pole help prevent slippage. Spiderbeam fiberglass poles are extremely strong, with a much greater wall thickness than the typical "fishing rod" types.It uses a special reinforced winding technique – where several layers of fiberglass are wound in alternating direction (criss-cross wound) – providing greatly increased lateral and linear strength. The Spiderbeam Mini-poles have a much larger overlap between segments than most other fiberglass poles, which assures stronger joints between segments, and results in a much stronger pole. Spiderbeam fiberglass poles are perfect for supporting all kinds of wire antennas.The Spiderbeam Mini poles are great for Geocaching, SOTA, IOTA and any other popular application for traveling ham radio operators. The top segment of the Mini pole is hollow, very rigid and got has a usable inner diameter of 4mm allowing a wire to pass through, or for attaching your mini tool for other applications. Unlike most competitors’ poles where the top segment is a very thin, solid whip, the Spiderbeam Mini pole can be used to its full 7m or 10m length. Technical Data 7 Meters / 23ft fully extracted length (height) 7m (23ft)* transport length 0.71m (2715/16)* weight 1026g (2lbs. 4 oz.) bottom diameter (incl. the cap) 50mm (2")* top diameter 6mm (0.24")* wall thickness 0,7mm - 1,4mm* (0.027" - 0.067")* number of segments 11 pole material black fiberglass, UV protected specially reinforced multilayer winding Technical Data 10 Meters / 32ft fully extracted length (height) 10m (32ft 10")* transport length 0.72m (281/3)* weight 2.220kg (4lbs. 14 oz.)* bottom diameter (cap) 66mm (2 3/5")* bottom diameter (segment) 60mm (21/3")* top diameter 6mm (0.24")* wall thickness 0.7mm - 1.4mm* (0.027"" - 1/18")* number of segments 17 pole material black fiberglass, UV protected specially reinforced multilayer winding

From €50.00* €58.00* (13.79% saved)

Details

Wire reel for antenna wire

Wire reel for antenna wire With this reel with 15cm diameter, the antenna wire of the Endfed or Mini Endfed can be wound up safely without bending the wire. Ideal for mobile use when traveling, SOTA (Summit on the Air) or DX expeditions etc. Simply wind the antenna cable onto the spool and stow it in your backpack or bag. The bright yellow color makes it easy to find the reel in your bag. 15cm diameter 24mm wide For about 22m antenna wire with 1mm2

From €4.90*

Details

Rope clamp

Rope clamp Clamcleat® CL260 - pack of 10 pieces Self-locking rope clamps made of high-strength, UV and cold-resistant material (tested in arctic conditions). Easily adjustable and retightenable at any time. For ropes of 2-4mm diameter. Ideal for Hamrope PES4. Material: nylon, color olive green or black, supplied in a pack of 10.

€7.50*

3x snaphooks A4

3x snaphooks A4Thanks to their rust resistance (material 316), these stainless steel snaphooks can be used permanently outdoors or in the wet. They have a length of 50 millimeters, with the snap hook measuring five millimeters in diameter. The total weight that this snap hook can support is 95dan, about 85 kilograms. This should be enough for tie-off. Technical data snap hook Length: 50 mmWidth: 25 mmInner length: 40 mmThickness: 5 mmInner width: 15 mmOpening: 7 mminner width eyelet: 8 mmmax. weight load 85 kgmin. breaking load 200 kg

€6.60*